Pixel blowing fuses
 
Notifications
Clear all

Pixel blowing fuses

10 Posts
4 Users
0 Reactions
2,884 Views
relic1882
Posts: 104
Topic starter
(@relic1882)
Estimable Member
Joined: 12 years ago
[#53265]

I'm having trouble with my larger tree this year. It seems somewhere with it something is blowing my fuse.

Is there an easy way to narrow down the bad pixel without just attaching one section at a time and blowing fuses until I find it? I'm hoping it's just a bad pixel somewhere because I don't have enough spares to replace an entire section and this tree is important in the show. I have a multimeter but I need to learn how to properly find what's blowing the fuse.

Thanks!

Sent from my moto x4 using Tapatalk


9 Replies
Posts: 120
(@superdave)
Estimable Member
Joined: 13 years ago

You don't give any real details on number of pixels, power supplies, controllers, etc. Have you ensured that your fuses are properly sized? You might just be pulling more amps than the fuse you are using. That isn't necessarily a problem, but you need to ensure your overall setup isn't overloading the related power supplies.

A good resource for determining some of this : http://spikerlights.com/calcpower.aspx

I think we've also seen plenty of times where the manufacturer has swapped wires inside the epoxy area of a pixel. It is rare, but people post examples every year. It could just be one pixel with wires crossed and causing it? That would take some fairly close visual inspection.


Reply
relic1882
Posts: 104
Topic starter
(@relic1882)
Estimable Member
Joined: 12 years ago
superdave wrote:You don't give any real details on number of pixels, power supplies, controllers, etc. Have you ensured that your fuses are properly sized? You might just be pulling more amps than the fuse you are using. That isn't necessarily a problem, but you need to ensure your overall setup isn't overloading the related power supplies.

A good resource for determining some of this : http://spikerlights.com/calcpower.aspx

I think we've also seen plenty of times where the manufacturer has swapped wires inside the epoxy area of a pixel. It is rare, but people post examples every year. It could just be one pixel with wires crossed and causing it? That would take some fairly close visual inspection.

The tree is made up of 85 ws2811 pixels coming from my falcon F16v2-R. There are 5 vertical rows in a series to make it. It's the first in line before the shorter trees from the controller port. Something along that port was blowing the fuse on the board and I narrowed it down to that tree because when I disconnected it from the series the problem went away. It worked fine the last time the lights were up but not now. I was hoping to find a better way to find the bad part without just going through fuses. It has to be a bad pixel or something but I can't find anything based on a visual inspection yet.

Sent from my moto x4 using Tapatalk


Reply
Posts: 120
(@superdave)
Estimable Member
Joined: 13 years ago

I'd expect you are doing power injection?

What happens if you lower the brightness levels(30%?)? Does it still happen then?


Reply
relic1882
Posts: 104
Topic starter
(@relic1882)
Estimable Member
Joined: 12 years ago
superdave wrote:I'd expect you are doing power injection?

What happens if you lower the brightness levels(30%?)? Does it still happen then?

There is power injection going to other places but when I was narrowing it down to the tree I had removed it from this line. Previously I injected power at the third tree. After the fuse at the board blew I removed that power injection from that run and the fuse on the board continued to blow.

I actually haven't tried to lower the brightness yet. I'll do that later when I get back out there.

Sent from my moto x4 using Tapatalk


Reply
Page 1 / 2
Share: