New Pixel IC Coming
 
Notifications
Clear all

New Pixel IC Coming

33 Posts
19 Users
0 Reactions
11.5 K Views
timon
Posts: 2149
Topic starter
(@timon)
Noble Member
Joined: 16 years ago
[#30008]

I can talk about a new pixel IC that's coming soon. Basic information has been released to the public so I have no problems talking about it now.

The IC is called the WS2821 and it's made by World Semi plus another manufacture. It comes in four version, a 8 pin, a 14 pin, and two 5050 RGB packages much like the WS2811 and the WS2812A/B. So far nothing special right?

Well, there is something special, it's not a SPI type part like the WS2811, it's DMX, that's right DMX. Other than a RS485 to TTL converter you can feed DMX directly to the part. There have been DMX chips in the past but not packaged this way and a such a low price point.

The parts connect in parallel so the failure of one will not effect any of the rest on the string. Wait, there is more. You can write the address into the chip. If the information I have is correct, albeit it may not be, each chip can have its own address.

In addition you can run these at not only 250Kbps but also at 750Kbps with auto baud rate detect. This will allow you to drive more than 170 pixels per string but that will require a E1.31 controller mapping multiple universes to one string but that's no different than what's being done with the WS2811.

That's as much information as I have right now other than there will be a version of the Technicolor that will use this chip.

Ray will have samples in the next couple of weeks and he'll be sending me strings to test. Additional strings will make their way to other as well. I'm redesigning the Pixel Flower to use them as they are going to be much easier to use than the WS2811 types.

I think that 2014 is going to be a fun year.


32 Replies
Lionking_Tx
Posts: 780
(@lionking-tx)
Prominent Member
Joined: 15 years ago

What's Ray's word on improving quality ?


Reply
Posts: 2128
(@livermore-dad)
Famed Member
Joined: 16 years ago
Lionking_Tx wrote:What's Ray's word on improving quality ?

He only talks to timon 🙂 Sell anyone anything , but if there are issues, well ya you are on your own.. We need to figure out the system that Timon has worked out with Ray. Timon sends him an American Beer every time Ray responds? 🙂 hahahaha

Tory


Reply
Posts: 499
(@frederic)
Honorable Member
Joined: 14 years ago

I'm glad I haven't pulled the trigger on purchasing pixels... I am likely going to wait for these...

I only saw the announcement on WS' facebook page, not their website.


Reply
Posts: 844
(@ags0000)
Noble Member
Joined: 16 years ago

By "connect in parallel" do you mean the data line (rather than current serial pass-through)? That would pose a huge load to drive many pixels, wouldn't it?


Reply
Posts: 853
(@roterhead)
Prominent Member
Joined: 15 years ago
ags0000 wrote:By "connect in parallel" do you mean the data line (rather than current serial pass-through)? That would pose a huge load to drive many pixels, wouldn't it?

If true DMX there will be two differential data lines, so V+, V-. D+, D-. They could be making some assumptions on wire length thus minim, loading on the data lines.


Reply
CaptKirk
Posts: 2200
(@captkirk)
Noble Member
Joined: 16 years ago

If they are really in parallel, the DMX512 standard does not allow more than 32 devices tied directly to the RS485 bus without having to regenerate the DMX data stream. Hopefully there is a Din Dout that regenerates the DMX data stream for each chip otherwise the data it is gonna get pissy really quick!


Reply
Posts: 499
(@frederic)
Honorable Member
Joined: 14 years ago

Remember, DMX is just a protocol.

RS485 is a wiring/communication standard, and it's the latter that limits multi-drop communications to 32 devices.

Just because it's "typical" to run DMX over RS485, it doesn't have to be. It can be run over any serial link that has enough bandwidth to accurately transport the 250K data and in fact, that link doesn't even have to be wired or radio - it could be a modulated laser beam.

RS485 was chosen because back in the day, it was the best there was at the desirable price point.


Reply
timon
Posts: 2149
Topic starter
(@timon)
Noble Member
Joined: 16 years ago
Livermore-Dad wrote:He only talks to timon 🙂 Sell anyone anything , but if there are issues, well ya you are on your own.. We need to figure out the system that Timon has worked out with Ray. Timon sends him an American Beer every time Ray responds? 🙂 hahahaha

Tory

I not sure how to read that. Anyway, I'm not the only one that talks with Ray but I seem to have a good relationship with him. I can't agree that Ray leaves you on your own when there is a problem. From everything I know he's worked very hard to make people whole over the issues on the Technicolor Pixels.

ags0000 wrote:By "connect in parallel" do you mean the data line (rather than current serial pass-through)? That would pose a huge load to drive many pixels, wouldn't it?
Roterhead wrote:If true DMX there will be two differential data lines, so V+, V-. D+, D-. They could be making some assumptions on wire length thus minim, loading on the data lines.
CaptKirk wrote:If they are really in parallel, the DMX512 standard does not allow more than 32 devices tied directly to the RS485 bus without having to regenerate the DMX data stream. Hopefully there is a Din Dout that regenerates the DMX data stream for each chip otherwise the data it is gonna get pissy really quick!
frederic wrote:Remember, DMX is just a protocol.

RS485 is a wiring/communication standard, and it's the latter that limits multi-drop communications to 32 devices.

Just because it's "typical" to run DMX over RS485, it doesn't have to be. It can be run over any serial link that has enough bandwidth to accurately transport the 250K data and in fact, that link doesn't even have to be wired or radio - it could be a modulated laser beam.

RS485 was chosen because back in the day, it was the best there was at the desirable price point.

The chip is uses TTL logic levels not RS485. If you want to connect directly to a DMX cable then you need a RS485 receiver much like the ones I'm working on and will hopefully release soon.

Here is how the chips are connected. Shown is the 5050 version but the IC version works the same way. R1 I believe is a 10K resistor. In actual use you would have a resistor on the ADI and ADO just like the WS2811 just to make sure you protect the IC.

999789 188344054705060 1975967719 n

My understanding is that the address in line works the same as the MY9943 when the chip is un-programmed. If you set the input high on the first chip in the chain then it starts at DMX address 1. The chip will raise its output high when its used three addresses. This works it way down the chain. I don't have the programming information yet so I cannot tell you exactly how they are programmed yet. WS has not released the programming information as they have a programmer they want to sell. I've ask Ray to press them on this because if they don't we'll just reverse engineer it anyway so they might as well release the information now. I hope to have that information soon.

What this does imply is that the pixel strings and strips will have 4 connections, +V, Data In/Out, Address In/Out and GND. The chips are designed for 19ma drive unless you use the 14 pin IC which can be set to drive up to 60ma. The chips can handle up to 24V just like the WS2811.


Reply
Posts: 238
(@ronp5683)
Reputable Member
Joined: 14 years ago

So when will there be software and controllers to support these new parts?

I also wonder whether it is wise to buy parts the first year they come out, kinda like Technicolor.


Reply
Page 1 / 4
Share: