In my daily work I use WS2811/WS2812b/UCS1903 IC's. Sometimes need to drive large, simple RGB "pixel" synchronised with rest of installation.
I was design a simple RGB driver as a one WS2811 pixel. Can drive 120W per channel without additional mosfet's cooling. 360W total output.
RGB outputs for RGB strips. 12V power supply.
I'm only a electronic hobbyst, not a PRO.
Here is board visualisation (rev. A)
P-channel mosfets?
N-chanell
Very interesting. I am cobbling together a controller also based on WS2811's and struggled to make the connect between the open collector style output of the WS2811's and N-channel mosfets configured as a low-side driver - I had to put something in between, either a PNP transistor, a small p-channel mosfet, or 74HCT gates (I chose the latter).
Nice. I'm working on something similar. Any chance you could post your schematic for this ????
dvc2013 wrote:Nice. I'm working on something similar. Any chance you could post your schematic for this ????
I can do that.
I've been working on this for several months now, mostly fighting the Eagle schematic capture software's learning curve (I'm slow). I have put together many styles of the design, but I'll share the two major ones.
The first drives external DC SSR's exactly the same way as Renard equipment does, which allows me to reuse what I already have. There's no ZC detection so this is for DC SSR stuff only:
The second has n-channel mosfets (FQPF13N06L 60V 10A) on-board wired as open-source drivers so they can be used with common-anode dumb RGB products (strips and strings) or in my case, to drive individual single color 12V LED's "bulbs." Even though the WS2811 chips were designed with RGB products in mind, a channel is a channel is a channel.
Neither schematic is complete because I'm still fighting with my learning curve with the software, and there are no board layouts as of yet for the same reason.
The reason why I chose to use an SN74HCT540 chip instead of what you did was simply to be able to make the boards smaller. A '540 will take up a lot less space than eight PNP transistors (and resistors) and invert the signal of the WS2811's for the n-channel low-side drivers. I'll be using surface mount parts as much as possible to keep the boards as small as possible.
I have some of the sections of the second schematic breadboarded and working, but not all of it because I ordered two solderless breadboards thinking that was enough real estate and I was way off on that so I ordered four more and am waiting for them to arrive.
Off to the left you'll see an 8-pin header - that's for an ESP01 module. The 3-pin jumper just to the right selects between the ESP module and the RS485 chip, giving me a choice between the two on every board. I could drive each board by wifi, or drive the first one in a chain and cat5 a bunch of them together in a cluster. The SN65LBC179P allows the boards to pass pixel data between them over larger distances than WS2811 chips can do. That is one part (of several) of the schematic I did breadboard and have been driving it with DIYLEDEXPRESS' 6-port bridge with one of the outputs set to "pixel".
If you look closely at the schematic around the ESP you'll see that I basically lifted Bill Porter's version of the ESP pixel thing, and the software I used was Sporatic's from his version.
One of the things that makes the HCT series octal inverter chip a natural for this is the output stages of the gates are essentially a mosfet driver - the output pin of every gate is tied to VCC or ground by a pair of mosfets, and there's no floating nonsense. They give nice crisp edges to the PWM outputs that the external logic-level mosfets really seem to like.
Neither are a final design. Only parts of been breadboarded so far, but what on the solderless boards seems to work so far.
The only thing that is "final" is the name - pixeldragons - because my 10 y/o son wanted to have the honor of naming the controller series, as "pay" for his ability to see the tiny little wire holes on the solderless breadboards that I just can't see anymore. And thus, they're pixeldragons 🙂
So far so good.
Multi WS2811 in one module is good idea, but for me, most important is only one pixel, who can drive large RGB plate (for example).
Ofcourse I can drive this pixel wireless, for example with my other controller - ESP12 Pixel Node. This small board (20x52mm) can drive houndreds of pixels.
ESP12 + 2 voltage regulators + 74HC245
Or another E1.31 controller based on arduino Nano
http://doityourselfchristmas.com/forums/showthread.php?42707-My-way-for-cheap-E1-31-240-pixels-controller-no-soldering-needed-8#post419860
dvj, thanks for posting the drawings for us. It gives me a couple of ideas for my project.
BTW, I'm right there with you on the Eagle learning curve. After 2 years I'm still struggling with it. I've been using DipTrace lately with a little better luck. If I'm going to home etch something I use ExpressPCB. Can't beat it for something small & single sided. You just can't generate any gerber files to have boards made. That is unless you use the ExpressPCB board service which is a little on the costly side.
Just my 2 cents.








