IP Address Issue wi...
 
Notifications
Clear all

IP Address Issue with SanDevices E682

33 Posts
14 Users
0 Reactions
18.7 K Views
Posts: 2
Topic starter
(@aggie84)
New Member
Joined: 9 years ago
[#47371]

Hi all, I'm setting up my first controller and have run into a problem right from the start. I am using a new SanDevices E682. I am connected via CAT5 to my computer. I performed the override function (4) and was able to enter the web controller at 169.254.74.73. Once into the controller, I changed the IP Address to 192.168.1.15. I then Updated the System Information and Restarted the controller. The problem is that I cannot access the controller on the new IP Address. I tried to ping it and nothing happens. I plugged the controller into my router, went into the router's setup and I don't see the controller anywhere. I have also gone back in to the controller with the override IP and see that my new IP is still shown as the new device IP. I just can't talk to it.
Can anybody help a noob out?

Thank you


32 Replies
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago

What is your computer’s IP address?


Reply
Posts: 209
(@marx1)
Reputable Member
Joined: 18 years ago

You need to set an IP address on your computer. When you plug directly in there is no DHCP server so your computer reverts to a 169.254.xxx.xxx address.

Here's a good guide on how to do it for most windows:
https://www.howtogeek.com/howto/19249/how-to-assign-a-static-ip-address-in-xp-vista-or-windows-7/


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

Try again to over ride the ip. Hold down the program button until it flashes 6 times. That should give you the IP of 192.168.1.206. Then type in the new ip and click save system info. After that just unplug the 682 and plug it back in. you should be able to access with new ip.
PS: Don't just hit restart. Unplug it.


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago
deonb wrote:What is your computer’s IP address?

Where the heck have you been? Been ages since I've seen you post.


Reply
Posts: 431
(@dkelly0802)
Honorable Member
Joined: 11 years ago

I had a crazy time getting my 6804 going. I couldn't access it at all. I took an old router used it as a switch with my computer and the controller hooked into it by Ethernet cables I restarted all 3 devices and was able to get to the sandevice configuration page. You should be able to use the default address.


Reply
Posts: 2
Topic starter
(@aggie84)
New Member
Joined: 9 years ago
Dkelly0802 wrote:I had a crazy time getting my 6804 going. I couldn't access it at all. I took an old router used it as a switch with my computer and the controller hooked into it by Ethernet cables I restarted all 3 devices and was able to get to the sandevice configuration page. You should be able to use the default address.

Thanks all, I'll give this a try when I can get back on it. I am assuming my IP address is 192.168.1.4 since, when I try to ping the E682 that is what comes up. I think unplugging might be the solution, I was just hitting the restart button. It is good to know tho that I can use the overrides to achieve a 192.168.1.206. I saw that in the instructions but since they said to use the "4" override, that's what I was doing. We'll see, thanks again

Sent from my SM-G935V using Tapatalk


Reply
Posts: 431
(@dkelly0802)
Honorable Member
Joined: 11 years ago

I think if you are going to do the force reset you need to use the address compatible with your network.


Reply
Posts: 1249
(@jstjohnz)
Noble Member
Joined: 17 years ago

I need to put together a tutorial on this but here's the basic procedure:

Two Scenarios:

Scenario #1, you are using a direct connection from controller to Ethernet port on a PC.

PC Ethernet should be configured for DHCP.
Reboot the PC after setting up the direct connection to the controller. When a PC starts up, if it's Ethernet port is configured for DHCP, and if no router is found to assign it an IP address, it will default to a random IP address in the 169.254.x.x range.

Now, use override 4 on the controller to force the controller to have a temporary IP address of 169.254.74.73. At this point you should be able to access the controller by typing that IP address into your browser. Skip ahead to SET PERMANENT IP.

Scenario 2: Computer and controller are connected to your LAN.

You need to determine the IP address range used by your LAN. One way is this. Press the Windows key, then type 'cmd' (without the single quotes) followed by enter. That will open a black command window. In that window type: 'ipconfig /all' (without the single quotes) then press enter.
That will spew out a bunch of text. Scroll through the displayed text and look for a section titled Ethernet adapter local area connection, or Ethernet Adapter Ethernet. Within that section look for an IPV4 address. Typically the IPV4 address will be something like 192.168.x.y. X is the value we're looking for. Depending on your router, you may also encounter IP addresses such as 2.x.x.x or 10.x.x.x.

Select the proper override depending on the IP address range:
for 2.x.x.x IP, use override 2 to set a temporary IP address of 2.2.2.2
for 10.x.x.x IP use override 3 to set a temporary IP address of 10.10.10.10
for 192.168.0.x IP use override 5 to set a temporary IP address of 192.168.0.206
for 192.168.1.x IP use over ride 6 to set a temporary IP address of 192.168.1.206
for 192.168.2.x IP use override 7 to set a temporary IP address of 192.168.2.206, etc

After doing the override you should be able to bring up the controller's web page by typing the temporary IP address into your browser's address bar.

SET PERMANENT IP This is the final step.

Note that the permanent IP address should be set based on the IP address range that will be used by the controller in normal operation. If you will be using a direct connect, then the permanent IP should be a 169.254.x.x IP address. If you will be connecting the controller to your LAN instead of directly to the PC you will want to sel.ect a permanent Ip address in the address range of your LAN.
On the upper left corner of the web page you will see the temporary IP address set in the controller. Below that is where you set the permanent IP address. As shipped, controllers have an IP address of 192.168.1.206.
For your first controller, I suggest setting the permanent IP address to one higher than this, so if you will be connecting to a LAN that uses 192.168.0.x addresses, use 192.168.0.207 as the permanent IP address of your first controller. As you add additional controllers, use the next sequential addresses. You should leave the factory default IP address unused to avoid an address conflict when setting up a new controller.

After setting the permanent IP address, click UPDATE SYSTEM INFO to save it. The new IP address will take effect on the next restart.


Reply
Posts: 43
(@worble7)
Trusted Member
Joined: 12 years ago

Don't mean to hijack the thread but i have a question i could not get the San device web page to come up looked in ipconfig my ip shows IPV4 address is and still is 10.0.0.120 (preferred) tried the 10.10.10.10 nothing (took a break) I come back and just started going through the force ip settings starting at 1 now when i get to 4 (169.254.74.73) bingo the page cames up did not set a permanent address because I'm still lost on that part turned off the computer now I can't get to the web page again frustrated any ideas? Thanks for your help. Jeff
P.S. I have a 2 year old E682 controller


Reply
Page 1 / 4
Share: