How to electrically...
 
Notifications
Clear all

How to electrically determine pixel string wire functions and direction?

18 Posts
8 Users
0 Reactions
5,822 Views
Posts: 1076
 Zeph
Topic starter
(@zeph)
Noble Member
Joined: 15 years ago
[#52337]

I received some ws2811 5V pixel strings with unlabeled wires and without labels or arrows on the LEDs. The string has male and female JST connectors, but there appears to be no reliable standard for input and output connections (right?). So I want to verify from scratch which wires are which, and which end is input... My thoughts:

1. Use Multimeter to measure the resistance between each pin (of 3) from one JST connector to the corresponding pin of the other. Power and ground will have low resistance, and the data line should not be harmed by being tested.

2. Of these two, how do I determine which is power and which is ground, without causing damage? Try with 3.3v? Put a suitable resistor in line with a 5v supply and measure current?

3a. Power up the chips with 5v on power/ground, and measure the voltage on the third wire of each JST connector. It should be close to +5 on the Data Out end, right? This would determine which end of the string is input and output.

3b: Alternate: send data from a controller to the third wire of both ends, and see which causes. Or would any damage be caused by sending data from a controller to the Data Out of the chips?


17 Replies
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Most commonly the side of the pcb with the chip going from left to right . gnd,DO, +V.


Reply
wilmar
Posts: 2115
(@wilmar)
Noble Member
Joined: 8 years ago

Do they have power injection wires aswell ?

Sent from my iPhone using Tapatalk


Reply
wilmar
Posts: 2115
(@wilmar)
Noble Member
Joined: 8 years ago

I have 3 different brands and all inlets are as follows


Sent from my iPhone using Tapatalk


Reply
wilmar
Posts: 2115
(@wilmar)
Noble Member
Joined: 8 years ago

The 4th set were 5 dollar sets and they are backwards from rest of them

Sent from my iPhone using Tapatalk


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
wilmar wrote:I have 3 different brands and all inlets are as follows


Sent from my iPhone using Tapatalk

Yours are exactly as I stated 🙂

Also the non ic side of the pcb should be a dead giveaway as to the input end ,
as the input wiring would be attached to that side of the pcb.
The opposite is true for the output end of the string .


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago
angus40 wrote:Yours are exactly as I stated 🙂

Also the non ic side of the pcb should be a dead giveaway as to the input end ,
as the input wiring would be attached to that side of the pcb.
The opposite is true for the output end of the string .

I have sets where the chip side are input so that is not a given way to I'd input. I have some pixels like yours. In my case one of the wires has printing on them. That turned out to be v+. You were on the right track. I'd the data line apply power and data to one end. If you get no lights swap to the other end. No lights? Reverse the power connects and the reverse ends if no lights. Only leave power on for a few seconds. Pixels CNA handle reverse voltage for a short time.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
MartinMueller2003 wrote:I have sets where the chip side are input so that is not a given way to I'd input. I have some pixels like yours. In my case one of the wires has printing on them. That turned out to be v+. You were on the right track. I'd the data line apply power and data to one end. If you get no lights swap to the other end. No lights? Reverse the power connects and the reverse ends if no lights. Only leave power on for a few seconds. Pixels CNA handle reverse voltage for a short time.

Are they 2811 ? I have dozens of the ws 2811 pcbs both in 12v and 5v from quite a few different vendors and the one commonality is the i/o sides of the boards .

My tls are the exact opposite , but the same hold true for the tls input is always on the ic side of the pcb .


Reply
Jguenther
Posts: 98
(@jguenther)
Estimable Member
Joined: 11 years ago

Cut a pixel off and try it. I’d try data in the middle and power/ground on either side. If it doesn’t work, swap power and ground and try again. If you fry it, oh well and try again.


Reply
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

I'm a bit confused. Why go through the trouble of cutting off a pixel and testing, or try to get a reading between pins? Your pictures have the markings where you can see them. 12v, DI (Data In), and Ground. Simply look to see what color wire is attached to each solder pad.

If your concern is which wire goes to which part of your plugs, then pierce the ground wire with a pin and then measure continuity between that piercing (tap the pin) and find it in the plug. Do the same for each of the others, if necessary. This method does not do any harm to your pixels. If you feel the need, fill the pin hole with something such as liquid tape.

One little trick that has been around for a very long time - if your covering is not "clear", simply wet your finger and rub the moisture across the outside of the pixel. The markings inside will show much better.


Reply
Page 1 / 2
Share: