FPGA based pixel co...
 
Notifications
Clear all

FPGA based pixel controller

85 Posts
18 Users
0 Reactions
33.5 K Views
Posts: 238
Topic starter
(@ronp5683)
Reputable Member
Joined: 14 years ago
Zeph wrote:Have you looked into the TM1829? Similar to the 180x and 281x protocol and timing, but comes in 800 KHz and 1600 KHz flavors, and I have't yet seen software support for the latter (I'm thinking that you may have an advantage there, which is part of why I bring it up).

http://www.aliexpress.com/store/701799/search?SearchText=tm1829

Zeph, if you want to use these pixels, I will help you with a controller to support them. The web site at Rays, does not say if they are low or high speed. I will get my eight universe controller back this week. Hope there are no mistakes!!!

Finished one of my display boards for the side of the garage. It is 20x16 using WS2812B pixels. 🙂


Reply
Posts: 1076
 Zeph
(@zeph)
Noble Member
Joined: 15 years ago

I appreciate the offer!

I'm not yet sure which pixels I'm going to use, but I'm still enjoying having direct control via Arduino code that I understand. I find the FPGA stuff fascinating magic, but there would be a lot of learning curve before I could have DIY fun modifying it myself. I'm just aiming for 1D array with small distributed wireless controllers, so I don't need a lot of bandwidth at a single point.

However, it would think that for people working on video, the 1.6 Mbps data rate would be valuable, and an FPGA solution would really support the bandwidth they want! The only thing I know of that's faster is the 8806 but that's 4 wire.

Some of Ray's listing do now say high speed I think I recall but I would check with him before ordering...


Reply
Posts: 1249
(@jstjohnz)
Noble Member
Joined: 17 years ago

I have some 1829s from Ray but haven't tested them yet. He says they are the low speed. IIRC there is an initialization mode on the 1829s where you can set the actual current range to send to the LEDs. One of my concerns is what that defaults to if you don't initialize it.


Reply
Posts: 238
Topic starter
(@ronp5683)
Reputable Member
Joined: 14 years ago
jstjohnz wrote:I have some 1829s from Ray but haven't tested them yet. He says they are the low speed. IIRC there is an initialization mode on the 1829s where you can set the actual current range to send to the LEDs. One of my concerns is what that defaults to if you don't initialize it.

Thank so much for the feedback, you are too kind. I would hope that they would provide a good nominal initialization like on the Ethernet physicals. Also, if you happen to have a link to an English version of the data sheet I would appreciate it.

Also, if you have a chance to give feedback to Ray, tell him I want a WS2812 with 12-bits of PWM and the dimming curve in the controller. If they know the LED type this should be easy to characterize and include in the controller. This would simplify things a lot for us and keep the controllers/software at eights bits.


Reply
Posts: 238
Topic starter
(@ronp5683)
Reputable Member
Joined: 14 years ago

This is a demonstration of my 32 universe (16384 channel) pixel controller. I convert from Ethernet to pixel output 6120 channels in this demo, which uses about half of the controller outputs. The idea behind my controller is to be able to add channels as you need to update your display, with the channel cost being very low. The output for each channel is run through RS-485 buffers to receivers at each pixel string and the driver has been tested to 200 feet.

The pixels run in the sign are as shown below:
Sign 75x16 pixels (run from four Ethernet cables)
Two signs 20x16 (one Ethernet cable)
Four spiral trees 50 pixels (one Ethernet cable each)


Reply
Page 16 / 17
Share: