I'm having some issues with flickering pixels where two segments join together and I'm not sure what is going on. Any thoughts on the matter would be appreciated. Here's the scenario:
New installation (first year), I have 12v pixels along my roofline (110 nodes) with 8 small wall washers or floods mixed into the chain. I am injecting power at both ends of the roofline as well as in the middle and have broken up the segments accordingly to get a good balanced distribution of power with no segments longer than about 20 pixels or about 16 feet without power injection. The whole roofline chain is being driven from a Komby RF1_12v. After all the initial installation and troubleshooting and determining where segment divisions were too long or possibly needing null pixels I have all of the pixels and floods working with no null pixels and they are all responding to the commands from the vixen 3 software and Komby sandwich transmitter. The problem is that the last two pixels from the first set of segments on the first power supply, as well as the first two pixels on the second set of segments on the second power supply flicker kind of pink or purple whenever I send it an all white mode or a when they light up in a white chase pattern. I have verified voltages at the end of the first and the beginning of the second segments and I am reading about 12.2v-12.3v. Each pixel lights up with individual red green and blue colors, seemingly without any issues. All wiring is 18ga. The total length of the first set of segments is about 25-30 feet with power injected at multiple points, but the first pair of pixels in question are at the end of that run. There is about 8 feet of 2-wire cable (data, gnd) between the first and second sets of segments. It is at the beginning and end of that cable where I am having the issue. I even tried replacing that piece of cable with a null pixel and the problem continued while the "null" pixel looked just fine.
Any thoughts?
Update: I just climbed up and checked, and I'm having the same exact issue at the dividing line between power supplies 2 and 3.
Do you have all your negative lines connected together to make 1 common one for everything?
MrSmoofy wrote:Do you have all your negative lines connected together to make 1 common one for everything?
Yes I do have them all connected for a common reference point. I'm not opposed to checking it again though to make sure I haven't missed something.
Since the problem is occurring at the breaks, it sounds like either a ground or signal problem.
When you say you have "them all connected for a common reference point," do you mean the pixels themselves or the power supplies? The power supplies also need a common ground and there might also be a problem if the power supplies are coming from different household circuits.
HTH.
\dmc
dmcole wrote:Since the problem is occurring at the breaks, it sounds like either a ground or signal problem.When you say you have "them all connected for a common reference point," do you mean the pixels themselves or the power supplies? The power supplies also need a common ground and there might also be a problem if the power supplies are coming from different household circuits.
HTH.
\dmc
That is a great question and observation. I was meaning the pixel chain themselves (12v side of the power supplies) were all connected in common, but let me try to put further details into how I have things set up.
The line voltage side is all from the same circuit. When I built the home, I had put in three outlets under the soffits, one on each end of the house and one in the center by the front door. All three outlets are wired back to one switch location inside the house, where I have a timer switch installed to energize all three outlets on the same circuit. Those three outlets are the ones I'm using now for the three 12v power supplies (120vac to 12vdc, 6A each). On the 12v side I have connected the -12vdc as one continuous chain to all pixel segments and all three power supplies. The +12vdc lines of each group of segments are only connected to the +12vdc of their associated power supply. The data line starts at the Komby RF1_12v and runs in and out of all 118 total nodes (110 bullet style pixels and 8 floods). I should also note that in order to get the pixel spacing I am looking for, I have added short extension pieces of 18/3 in between each pixel, with soldered connections and covered with individual heat shrinks.
Does that help shed any more light on the matter? What about how you mentioned a possible signal problem?
