Falcon and Renard s...
 
Notifications
Clear all

Falcon and Renard setup help please

13 Posts
5 Users
0 Reactions
3,727 Views
Posts: 35
Topic starter
(@fearnold)
Trusted Member
Joined: 19 years ago
[#50171]

Hello all,

I purchased a falcon this year and I cannot make my rens work at all. Here is my setup. Laptop, network cable to router, network cable from router to falcon f16 v3, Dmx converstion cable from falcon to ren ss24. If I put the falcon in test mode either using the web interface or buttons on falcon, pixels on falcon and incandescents on ren respond. But I can not create a vixen sequence that gets a response from the ren. I do not understand xlights and really want to keep using vixen. I downloaded xlights and when I put it in test mode I find that the ren is in u 16. Running 2 network cables from computer to falcon and ren really is not an option so I really need the falcon to be the brains of the operation. Any input from anyone would be greatly appreciated. I have a very sad pixel tree standing in my yard doing nothing. Thank you in advance.
Frank


12 Replies
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

most likely you have not given the falcon the proper starting address for the channels you want too output (assuming you have properly patched the outputs in vixen).


Reply
Posts: 168
(@jvalue)
Estimable Member
Joined: 16 years ago

Ditto on Martin's comment. Export your sequence and note the channels vixen has configured.
Jim


Reply
Kev7274
Posts: 2037
(@kev7274)
Famed Member
Joined: 13 years ago

What port are you using for the Renard? Make sure you use port 2 or 3.


Reply
Posts: 35
Topic starter
(@fearnold)
Trusted Member
Joined: 19 years ago

I was afraid of this. I have no idea how to do that


Reply
Kev7274
Posts: 2037
(@kev7274)
Famed Member
Joined: 13 years ago

With the Falcon facing you,the 3 ports are on the right hand side. The far port is port 1,then 2 ,then 3. I had an issue with my Renard SS24 not working because I had it plugged into port 1. I put it in port 2 and it worked.


Reply
Kev7274
Posts: 2037
(@kev7274)
Famed Member
Joined: 13 years ago

Here's the link to the manual if you don't have it.
https://docs.google.com/document/d/1S67ZVLgQRYsdqPhgfPkQucnFXvu1FmQAME9qnK5RixU/edit?usp=sharing


Reply
Kev7274
Posts: 2037
(@kev7274)
Famed Member
Joined: 13 years ago

Make sure under "Serial Outputs" that you have TYPE set as Renard,baud rate as 57600 and stop bits as 1. There was a bug where after saving the wrong baud rate and bits would show up,not sure if this is still true.

You can use this http://ipaddress/serialsettings.xml to see what baud rate for #2 is,it should say b="2".
Put in the ip of the Falcon.


Reply
Posts: 35
Topic starter
(@fearnold)
Trusted Member
Joined: 19 years ago

I do not know how to export the file you are speaking of. I’m using port 2 and I made the conversion cable. In test mode the ren lights up all channels so it must be the falcon address issue. In vixen I added a streaming 131 and a ren. I patched a mega tree to the falcon and a general numbered item to the ren. In the falcon web interface I have serial tab I have all 4 ports set to start channel 1. Baud 57600, n,1 I’ll reread the falcon manual thanks to all so far.


Reply
Posts: 168
(@jvalue)
Estimable Member
Joined: 16 years ago

Hi Fearnold,

Maybe the start channel of the renard is the issue. have your tried bypassing the falcon? My renards are all in front of the e131 because the start channels in those devices are limited to the low end of the channels in this channel hungry pixel world. To see what vixen is viewing the channels/patching, open a sequence, go to sequence -> export -> falcon sequence player. It will run for a moment and show you the start channels for your show.
Jim

Jim


Reply
Page 1 / 2
Share: