F48 Differential Co...
 
Notifications
Clear all

F48 Differential Controller - n00b Question

41 Posts
16 Users
0 Reactions
39.4 K Views
Posts: 14
(@sethof)
Active Member
Joined: 9 years ago

The F48 appears to be similar to an F16v3 with 2 expansion cards

The F16v3 allows a maximum of 1024 pixels per output if solo that is for the initial 16 outputs. If you add an expansion card, the 1024 is split between the first 16 outputs on the main board and the next 16 outputs on the expansion card. (For example 512+512=1024 per output) If you add a second expansion card, then it is split again over 3 sets of outputs (example 350+350+324=1024) In this instance the main board outputs are limited to 350 pixels, the first expansion card 350 pixels per output and the second expansion card 324 pixels per output.

For the F48, the first 4 sets of RJ45 (1-4, 5-18, 9-12, 13-16) correspond to the main F16v3 card, the second set (17-20, 21-24, 25-28, 29-32) the first expansion card and the third set will be the second expansion card.

The distribution of pixels is available on the web interface to adjust as needed

1

Reply
Posts: 73
(@zwiller)
Trusted Member
Joined: 17 years ago

Yes, essentially these controllers are the same in terms of max pixels so nothing new there but I think this is design more toward the distributed style layout and many of us using it do not power inject at all. I think once folks see a few different iterations of powering 4 port receivers they will then see the benefit. No more daisy chaining stuff. I am not sure myself yet but thinking of putting the receiver and 180W PS in a small CG case or maybe creating a power bank with PS and distros in a marine case and running DC to receivers in a tiny TA200. You could even mount to a prop and forgo pigtails.

Al's comparison of the old school SSR concept is spot on if you ask me. It's kinda funny, in the middle of the summer I sent Pitts a PM and said, hey why don't you make a controller with only sender ports for those little receivers and he said he was thinking about it and here we are... In the end the best way to do anything is what works for you. If daisy chaining 50k pixels to a 16 port board works so be it. Not for me tho. Another benefit of the multi controller/distributed layout is that I can add/change stuff with little effort. I have ports and headroom everywhere.


Reply
Posts: 48
(@whyintheworld)
Trusted Member
Joined: 10 years ago
Zwiller wrote:Yes, essentially these controllers are the same in terms of max pixels so nothing new there but I think this is design more toward the distributed style layout and many of us using it do not power inject at all. I think once folks see a few different iterations of powering 4 port receivers they will then see the benefit. No more daisy chaining stuff. I am not sure myself yet but thinking of putting the receiver and 180W PS in a small CG case or maybe creating a power bank with PS and distros in a marine case and running DC to receivers in a tiny TA200. You could even mount to a prop and forgo pigtails.

Al's comparison of the old school SSR concept is spot on if you ask me. It's kinda funny, in the middle of the summer I sent Pitts a PM and said, hey why don't you make a controller with only sender ports for those little receivers and he said he was thinking about it and here we are... In the end the best way to do anything is what works for you. If daisy chaining 50k pixels to a 16 port board works so be it. Not for me tho. Another benefit of the multi controller/distributed layout is that I can add/change stuff with little effort. I have ports and headroom everywhere.

I have an upstairs window that I want to make a matrix. Since it is up on the second story I haven't figured out how to mount a P10 matrix up there considering the weight. Mounting it inside the window isn't an option because it has multiple panes with dividers.

So I planned a 2" spacing matrix which makes it 1500 pixels. I could configure that group of ports to use 400 pixels and use the 4 port receiver board without pigtails attached right to the matrix as long as I power inject. That way I can store the matrix with the board right on it and just have to connect the power injection and the cat 5 signal next season... Something to consider.


Reply
Posts: 486
(@uncledan)
Honorable Member
Joined: 11 years ago

Just a thought... F4v3 is another option and is more flexible than F16v3. F4v3, diff expansion and two receivers is capable of 1024 pixels on ALL ports of F4v3 and the receivers. 12 outputs of 1024 pixels. I prefer my F4v3's to my F16's because of this.


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

Its all about personal preference at this point.


Reply
Posts: 48
(@whyintheworld)
Trusted Member
Joined: 10 years ago

Do the individual receiver boards need power? Lets say I'm going to power the pixels via injection from a PS located on the opposite side of the prop because the power happens to sit between two prop already and I'm going to inject at the "fold" or joint of two strings. But I wanted the controller on the other side to have input at the start of the string.

Can I just run the receiver board by only plugging the cat5 to the input and the negative and signal out to the lights or do I also need to run a power source to the receiver board itself?


Reply
Posts: 14
(@sethof)
Active Member
Joined: 9 years ago
Whyintheworld wrote:Do the individual receiver boards need power? Lets say I'm going to power the pixels via injection from a PS located on the opposite side of the prop because the power happens to sit between two prop already and I'm going to inject at the "fold" or joint of two strings. But I wanted the controller on the other side to have input at the start of the string.

Can I just run the receiver board by only plugging the cat5 to the input and the negative and signal out to the lights or do I also need to run a power source to the receiver board itself?

The receiver boards need their own power.


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago
Whyintheworld wrote:Do the individual receiver boards need power? Lets say I'm going to power the pixels via injection from a PS located on the opposite side of the prop because the power happens to sit between two prop already and I'm going to inject at the "fold" or joint of two strings. But I wanted the controller on the other side to have input at the start of the string.

Can I just run the receiver board by only plugging the cat5 to the input and the negative and signal out to the lights or do I also need to run a power source to the receiver board itself?

Haven't tried this myself, but it should work. The receiver board does need power. But you should be able to power it from the pixel string. Power isn't directional. It goes both ways down the wire. If the pixel string is powered from somewhere downstring, just connect all 3 wires to the receiver and that would backfeed power into the receiver board. It should power up and work fine.


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago
jchuchla wrote:Haven't tried this myself, but it should work. The receiver board does need power. But you should be able to power it from the pixel string. Power isn't directional. It goes both ways down the wire. If the pixel string is powered from somewhere downstring, just connect all 3 wires to the receiver and that would backfeed power into the receiver board. It should power up and work fine.

Will the receiver run at 12v? If not then when using 12v pixels you will need to provide 5v for the receiver


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago
MartinMueller2003 wrote:Will the receiver run at 12v? If not then when using 12v pixels you will need to provide 5v for the receiver

The website says 5 or 12V. There isn't much on the board, but it does look like there's a regulator. Like I said. I haven't tried it.


Reply
Page 4 / 5
Share: