EspixelStick v4.X I...
 
Notifications
Clear all

EspixelStick v4.X Install Problem

67 Posts
6 Users
0 Reactions
12.2 K Views
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
MartinMueller2003 wrote:This is a failure to upload to the ESP. It almost looks like you need to manually put the device into programming mode and that did not happen. If you are manually putting the device into programming mode, you will need to do so multiple times.

That is part of the issue Martin. I had to connect d0 to ground . This should not have to be done as the v4.zip works fine .

Also , once it does actually write , erasing the wemos can be troublesome throwing efuse errors etc.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Is there any substantial benefit for updating the wemos 8266 beyond the v4.zip ?

There is a single ws 2811 output and a single relay/servo output made available .
If further updates enabled more GPIO I could see a need otherwise the Esp32 is the update to lean towards. :freak:

Just my thoughts .


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
gatoruss wrote:Yes. I can successfully upload the v4.0-beta4 .zip and connect to the Network. Initially I had an issue connecting to 5v, but I tried another version of the device and the 5 volt seems to work fine (the device I was initially using must have had a defect).

You are golden then ....happy lighting.


Reply
Posts: 49
Topic starter
(@gatoruss)
Trusted Member
Joined: 5 years ago
angus40 wrote:You are golden then ....happy lighting.

Thanks for your help.:biggrin2:


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

I just dug out my D1 Mini (man that thing was under a lot of stuff). Yes there is an issue burning the ESP D1 Mini image. It crashes over and over.
Uploaded a build from platformio and there is no crash.


Reply
Posts: 49
Topic starter
(@gatoruss)
Trusted Member
Joined: 5 years ago

I had ordered a MELIFE ESP32-DevKitC core Board for ESP32 Development Board ESP32-WROOM-32U from Amazon and it just arrived. This device comes with an external antenna enabled and there is not need to move a microscopic 0 ohm resistor.

I successfully installed the firmware from the google drive -- using D1 DevKitC as hardware. It installed fast, but after the install the serial monitor froze while the device booted up (log attached). However, when I logged onto my router I saw that the device was connected with an IP address. I was able to access via the webpage.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
gatoruss wrote:I had ordered a MELIFE ESP32-DevKitC core Board for ESP32 Development Board ESP32-WROOM-32U from Amazon and it just arrived. This device comes with an external antenna enabled and there is not need to move a microscopic 0 ohm resistor.

I successfully installed the firmware from the google drive -- using D1 DevKitC as hardware. It installed fast, but after the install the serial monitor froze while the device booted up (log attached). However, when I logged onto my router I saw that the device was connected with an IP address. I was able to access via the webpage.

Did you get the 5g antenna ?


Reply
Posts: 49
Topic starter
(@gatoruss)
Trusted Member
Joined: 5 years ago
angus40 wrote:Did you get the 5g antenna ?

I already had dual band.


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

New version has been uploaded to the google drive. I turned off Relay support on the ESP8266 builds. It was causing the startup to fail. Not sure why but this is a workaround to getting people moving. Tested the flash tool on my D1Mini and it works properly for this version.

https://drive.google.com/file/d/1DG3wz8lbYNc371OIbeOqkzMaY5Zd2SKA/view?usp=sharing

Martin


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Curious .
What is the issue with the v4.04.zip other than it being older from the release page that requires this ?


Reply
Page 3 / 7
Share: