blantrip wrote:The problem I mentioned about last year's ESPixelsticks not connecting has been solved. I have to admit my own stupidity. Since I was having the problem flashing new ESPixelsticks, I thought I had a problem with my other ones as well. Turns out, the ip address that I wrote on the first arch I tried was incorrect. Once I used the correct ip address, all is well with those.Now about the new ones I'm trying to flash and assign a static ip to. Attached are screen captures of what I see when I first flash it, and then what I see after assigning a static ip address in the serial monitor window.
It's been a while since I've tested static IP's, I'll look into this evening.
worksopian wrote:Not sure what, if anything, I did different but it works now!?
Good to hear, let me know if you run into any other issues.
thanks,
-shelby
sporadic wrote:It's been a while since I've tested static IP's, I'll look into this evening.Good to hear, let me know if you run into any other issues.
thanks,
-shelby
Thanks. I’m good at the moment. In lieu of setting a static ip, I’ve reserved the DHCP assigned ip address in my router configuration, so it should work ok during the show.
i have the same problem, i have build 4 and they work fine, can change the ip and name. but now i can't change the namen and ip. when i do that, i can't connect the stick.
When i flash him again it's works fine but, can't change anyting.
Can't find the problem. i use the same programmer, and the same file. I have 3 types off ESP and try them all. Now i take one that works fine. program it again and have now the same problem with this one.
Now i only have 3 thats works fine. the ohter one i can program, but when i change something name or ip adres than it won't work anymore. When i change the universal channel or pixel counts its not a problem.
i see this on my programmer
ets Jan 8 2013,rst cause:4, boot mode:(1,0)
wdt reset
I think i found a problem, look with a microscoop to the ESP and foud out that all off the ESP i orderd by Ali express won't work.
The others i buy in the Netherlands works fine.
I did them in the same box, now i sort them to look on the print and saw some diverence so i can sort them.
what's wrong with the ali-express esp's? I have different type of esp's all from different ali-express vendors; i think about 40 in total. They all programmed and work fine.
As I recently found out... you should not reverse polarity :biggrin2::biggrin2:. Cost me 3 esp's. I had one spare and managed to screw it in place with a screw terminal 3 minutes before showtime (150 people waiting:biggrin2:
Where do you live in the Netherlands?
Found out that on the working ESP'S "Al-Cloud inside" stands on the print. Have 10 working ESP's ( from diverent shops incl ALi) but with the last 20 ESP's if have this problem. All the others i don't have a problem. use the same programer and flash file.
I flashed 10 ESP-01S. I assume the router assigns them a address. I need to know how to assign them a address manually because all but one have a duplicate address.
11Bravo wrote:I flashed 10 ESP-01S. I assume the router assigns them a address. I need to know how to assign them a address manually because all but one have a duplicate address.
If the router assigned them an address, then they would not get duplicate addresses. It sounds like your image does not have DHCP enabled. The original versions had a place where you could set the address at compile time. You can also bring them up one at a time and set the address via the web interface.
mdnooyer wrote:I think i found a problem, look with a microscoop to the ESP and foud out that all off the ESP i orderd by Ali express won't work.
The others i buy in the Netherlands works fine.
I did them in the same box, now i sort them to look on the print and saw some diverence so i can sort them.
Just FYI... I've had a similar problem with a few ESP-01's I picked up on Amazon. If you change any of the settings and save... the config.json gets corrupt and the board stops working. On mine, the power light just flashes blue when this happens. I've stepped through the code and it fails in loadConfig (logs a ' Configuration File Format Error ').
It looks like there are some ESP-01's that can't handle modifying anything in SPIFFs? i plan on writing a quick test app this weekend to see whats going on.
You can get around this problem by modifying the config.json file ('spiffs' folder in the flash tool) with all your settings then upload.
