E682 Firmware Versi...
 
Notifications
Clear all

E682 Firmware Version 4 Beta

113 Posts
24 Users
0 Reactions
31.2 K Views
Posts: 1249
Topic starter
(@jstjohnz)
Noble Member
Joined: 17 years ago
[#25239]

Please note: Version 4 firmware will NOT run on any controllers that have the old ethernet modules. This means that E680s and E681s MUST have the UPG1 upgrade installed in order to run version 4. If you install version 4 on a controller that does not have the new ethernet module the board will not work.
05/19: bombshell tonight! NO new version! Just a new .doc file for the E6804/firmware V4 combination. I'm attaching that to a separate thread because I'm maxed on number of attachments here.
Thanks again for everyone's efforts. With the updated documentation now available, I'm about ready to put the E6804 on the web sit and start shipping with the new firmware.
05/15: version 4.026 added, there was an issue wioth 4.025 that would not allow it to be loaded via the lan update procedure.
05/16: version 4.025 fixed bug re not allowing 000 in ip adrs, replaced erase config memory button with a system command button, system commands are:
10: erase config memory, 20: load test defaults of 4 50-pix strings of 2801s on each cluster addressed from 0, and 30: load 'as shipped' dflt pixel types
for some reason it's not letting me upload the e6804 file version... see post#64 for vers 4.025 for E6804
05/15: version 4.023 I did finally reproduce the garbage IP issue and believe it is fixed, of course I said that yesterday....
05/14: vers 4.020 attached. I have not been able to reproduce the garbage IP issue but I did find a bug that may have been causing it. I would appreciate it if those with this issue would try 4.020 and let me know.
05/13: vers 4.019 this fixes a bug re use of pixel grouping.
05/12: vers 4.018 versions for all controllers with new ethernet module. Should fix issue re unable to upgrade via lan. Also re-worked zigzag logic.
05/11: vers 4.016 for E682 attached, improved timing for 2811s/1804s.
05/11: Vers 4.015 for the E682 is attached. Fixed an issue that caused the IP overrides not to work.

05/06: Vers 4.012 attached, for all useable hardware versions (must have new ethernet module). Adds Art-Net support.
Also updated documentation file.

Attached is the eeprom file for the version 4 beta firmware. This version is for the E682 only. It is very close to being finished, the only significant item missing is the ability to change the test pattern value from the web page. So, make sure test patterns are off before loading this firmware.

It should be fairly self-explanatory. There are a few buttons at the bottom of the page:
REFRESH just refreshes the page, but doesn't change any configurations.
RESTART CONTROLLER does just that. You will need to restart after changing the IP address. All other config changes should take effect as soon as you click the proper submit button, no restart is necessary.
ERASE CONFIG MEMORY zeroes out all of the configuration memory (except mac and IP addresses) and then restarts the controller. Use this if you see a lot of garbage on the config page after updating firmware.

Firmware may be installed via the lan or via a prop plug. You can revert to old firmware in the normal way, with this version you start a firmware update by clicking the button on the web form.

Unless you have a prop plug programmer, I wouldn't advise installing this on a board that must be running a live show. Although I was able to upgrade and downgrade the firmware with no isues in my testing, it's always possible that something weird may happen that could cause you to b unable to restore older firmware via the lan.

Feedback is appreciated.


112 Replies
Posts: 11
(@glevelius)
Active Member
Joined: 14 years ago

Jim, this is the single best upgrade I could ever see. I always had problems remembering the commands so this was a very welcome upgrade. Thank you for all your hard work!

-Gary-


Reply
Posts: 1249
Topic starter
(@jstjohnz)
Noble Member
Joined: 17 years ago

See post #1 for version 4.011, for all boards that use the new ethernet module. This version adds Art-Net support.


Reply
Posts: 1249
Topic starter
(@jstjohnz)
Noble Member
Joined: 17 years ago

See post #1 for 4.012 and updated doc file.


Reply
Posts: 339
(@dan-ross)
Reputable Member
Joined: 19 years ago

FYI the document has a typo. it has the line " For example, if you want code 5, you would hold the button down until the red and green LEDs come on for the
5th time, and release it before they come on for the 5th time." I assuming the second "5th time" should be 6th.


Reply
Page 1 / 23
Share: