E681 Paging (Config...
 
Notifications
Clear all

E681 Paging (Config Change) Application

17 Posts
7 Users
0 Reactions
4,646 Views
kidcole
Posts: 307
Topic starter
(@kidcole)
Reputable Member
Joined: 17 years ago
[#22713]

I am using the E681 in my show now and I am totally pleased with their Grouping feature. My mini RGB tree is a big hit in the show and to get it going quickly I grouped the Pixels on each strip into one pixel. It works perfectly and I was able to get it into my show in a couple hours ! I highly recommend this as a starting point for anyone doing pixels for the first time.

Next I plan to start activating all the pixels on each strip for some advanced color sequencing. And the E681 lets me define additional configuration pages that can be activated by turning on various DMX addresses. So this question is to the people who are using this feature (or maybe Jim will see my post) .. I know how to define Page 1 for what I need the E681 to do. But the user manual is not clear on how quickly the config can change pages. If I put it at the front of the song that uses that particular page, the song has already started by the time I am requesting the change. What is the recommended procedure for me to follow, since now I will have some songs using Page 0 and some songs using Page 1. Obviously I will need the page to be called up at the start of each song. How do I do this so I don't cause some sort of delay or glitch in the sequence ? It would be nice to see this added to the applications guide with a lot of detail !


16 Replies
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

I asked this same question in another thread - - frankly I'm not sure if many/any folks are using this feature - or they just don't know about it... I think the best thing to do would be to create a simple sequence sending the page number on channel 511 or 512 (don't recall which) and just use that between your real sequences in your playlist. I agree that the instructions are a bit sketchy - I assume the first socket is used but I don't know that...


Reply
Posts: 612
(@n-gifford)
Honorable Member
Joined: 15 years ago

Out of curiosity, what sequencing software are you using? I only ask because the ones that better support RGB pixels allow for grouping, so you can assign them individual addresses but group them in the sequencing software to give you the best of both worlds without the need to change the E681 config. Make sense?

For instance, I'm using LOR S3 with about 1,300 pixels. They're all addressed individually, but I have them grouped at multiple levels. So, I can control each any every light one at a time if I want, or I can control my rooflines as one, upper roof, lower roof, or even sections of each (Each roof line has different elevations). And sometimes (A lot of times, actually) I minimize the entire display to one group and control all 1,300 lights as if they're one channel. I've done the same thing with my arches, and strings on my tree. It works well, and I only use a single configuration for each E68x.


Reply
kidcole
Posts: 307
Topic starter
(@kidcole)
Reputable Member
Joined: 17 years ago
n_gifford wrote:Out of curiosity, what sequencing software are you using? I only ask because the ones that better support RGB pixels allow for grouping, so you can assign them individual addresses but group them in the sequencing software to give you the best of both worlds without the need to change the E681 config. Make sense?

For instance, I'm using LOR S3 with about 1,300 pixels. They're all addressed individually, but I have them grouped at multiple levels. So, I can control each any every light one at a time if I want, or I can control my rooflines as one, upper roof, lower roof, or even sections of each (Each roof line has different elevations). And sometimes (A lot of times, actually) I minimize the entire display to one group and control all 1,300 lights as if they're one channel. I've done the same thing with my arches, and strings on my tree. It works well, and I only use a single configuration for each E68x.

I am glad you pointed this out Nick. I am using LOR 3. And I tried grouping them strings with all the pixels inside. But when I would fill in some sequencing at the group level, LOR would only populate the first pixel at the top, and NOT all the pixels in the group. I had about 5 hours to go before my show when this was happening, so I used the e681 grouping feature instead. What setting or parameter am I missing my LOR setup that would assure that my sequencing at the group level would fill in all the pixels inside ?


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

I've been flipping between using LOR S3 and HLS - - both support grouping operations but I kind of like the LOR UI a little better than HLS. The only issue is that there is no Vixen -> LOR converter (that I'm aware of) so I need to create everything from scratch whereas HLS has a Vixen import ability saving me time. I'd like to see any tips for using LOR here.


Reply
Posts: 612
(@n-gifford)
Honorable Member
Joined: 15 years ago
kidcole wrote:I am glad you pointed this out Nick. I am using LOR 3. And I tried grouping them strings with all the pixels inside. But when I would fill in some sequencing at the group level, LOR would only populate the first pixel at the top, and NOT all the pixels in the group. I had about 5 hours to go before my show when this was happening, so I used the e681 grouping feature instead. What setting or parameter am I missing my LOR setup that would assure that my sequencing at the group level would fill in all the pixels inside ?

I'd be curious to see a screenshot of your sequence editor. Or a few for that matter, showing your grouping and channel configuration. The latter shouldn't make a difference, because you can sequence without any channels mapped. There's no magic to it, so I'd be curious to see exactly how you have it set up.

When I first added 'dmx devices' to the SE, they're all standard channels. I then convert (Mine) to RGB, then group them as needed and I'm done. I collapse a group, add an effect, expand the group and they're all populated.


Reply
jaywalk101
Posts: 761
(@jaywalk101)
Prominent Member
Joined: 15 years ago

I've been seeing a lot of folks here use LOR S3 for their pixel displays. How does this compare to something like LSP? I've used LSP 2.5 this year and really like the effects I can achieve with the macros and transition features. Does LOR have similar features that allow easy effect generation in a layer approach? Thanks!


Reply
kidcole
Posts: 307
Topic starter
(@kidcole)
Reputable Member
Joined: 17 years ago

OK .. Here's a couple screen shots. I opened up my RGB Blowmold Row as an example. This would be the same as one of the pixel strips .. think of it as 8 pixels. You'll see in screen 1 that I am showing a pattern in white and underneath that all three RGB rows have the same pattern (to make white). Next I close the group so I could see one row for the whole group. And I pasted in that pattern in again (to the right). I only pasted it once. What I wanted to happen was for that pattern to show up in all the "pixels" inside the group (if it was going to behave the same as when I have the whole strip grouped by the e681). In the Screen 2 shot you will see that it only populated the first row and not all of them. The other rows are still blank. How do you get yours to paste the pattern into all the pixels ?

Screen 1
Screen 2

Reply
Posts: 612
(@n-gifford)
Honorable Member
Joined: 15 years ago

I think I know what's going on. You said that in the second one, you pasted the effects. I'm assuming that you copied them from a single channel, and did not copy the whole group? That is the only time that it will not fill in all of the channels in a group.

For example, If I want to fill a group of 20 channels with effects from another group that has 5 channels. If they're both collapsed, so they appear as one channel and I copy the 5 channel group, then paste it to the 20 channel group, it will only fill in the first 5 channels in the 20 channel group. Does that make sense.

In the case of your screenshot above, you would need to copy all of the channels in the group if you want to paste it further down. You can do this by collapsing the group, copying the section of time that you want reproduce, then pasting it. Keep in mind that this will copy EVERYTHING in the group. So, if there are different effects that you can't see because the group is collapsed (You can only see effects from the first channel in the group), it will still copy them.

Hopefully that's clear as mud.... 🙂


Reply
Posts: 612
(@n-gifford)
Honorable Member
Joined: 15 years ago

FYI, this works in the opposite as well. If I copy from a 20 channel group and paste to a 5 channel group, the pasted effects will keep going as long as there are channels to fill and I may end up with 15 channels populated with effects that I did not intend to be there.

I've made this mistake a few times. It gets easier! 🙂


Reply
Page 1 / 2
Share: