DIY E1.31 Bridge an...
 
Notifications
Clear all

DIY E1.31 Bridge and Pixel extender setup

37 Posts
8 Users
0 Reactions
27.3 K Views
Posts: 59
Topic starter
(@arange98)
Trusted Member
Joined: 12 years ago
[#48714]

I have been using 3 channels of a DIY e.131 Bridge to drive a nonpixel show for the last couple of years. I build a pixel extender and tested it on a string of pixabulbs last year. I was able to get it to work using the test pattern thing in the bridge configuration page and even to control the strand with vixen 3 playlists.

Earlier this year I preordered 650 pixels, strips, etc. and a couple more pixel extenders from DIYledexpress which have now arrived, but I can for the life of me figure out how to configure the bridge and extenders to work. Now I've monkeyed with things to the point where the pixabulbs don't even work right.

I set the output to WS2811 with 150 channels as a test, but the behavior doesn't make sense and I certainly can't control them. I just wanted to test the pixels before plugging them in the strips and am pretty frustrated.

I would appreciate any links to basic setup stuff or screenshots of how it should be setup.

Thanks in advance.


36 Replies
dlovely
Posts: 3167
(@dlovely)
Famed Member
Joined: 17 years ago

What exactly is the problem? Are you running version 4.03? There was a fix for the different timings of WS2811 ICs.


Reply
Posts: 59
Topic starter
(@arange98)
Trusted Member
Joined: 12 years ago
dlovely wrote:What exactly is the problem? Are you running version 4.03? There was a fix for the different timings of WS2811 ICs.

I am running 4.01 so I may need to upgrade.

The problem is that the new pixels don't respond. I did get the Pixabulb strand to work again, but the new pixels still don't. I will have to figure out how to upgrade and then it will probably work.

Thanks much!
Allen


Reply
boyelroy11
Posts: 757
(@boyelroy11)
Prominent Member
Joined: 17 years ago

You'll need a prop plug to upgrade the firmware. I ran into this last season, and David worked through it, providing me beta firmware versions to find which worked with the newer pixels.

http://www.diyledexpress.com/index.php?main_page=product_info&cPath=22&products_id=161

I see they are sold out, but it is available elsewhere online.

Bruce


Reply
DrNeutron
Posts: 2018
(@drneutron)
Noble Member
Joined: 14 years ago

I can confirm that the new firmware will fix the timing issues with the new WS2811.
I was the one who asked if there was new firmware to address the new WS2811 timings last year, which Dave released the next day I believe. Awesome BTW!


Reply
mikeh65
Posts: 794
(@mikeh65)
Prominent Member
Joined: 19 years ago

I am going to join and follow this thread. I have been running two Bridges with a mix of Pixel and non-Pixels. But I also have not been able to get my new pixels to work. I also have 4.01 on my current bridge that I am testing with. I have ordered my Parallax Prop Plug. Once it comes in I will do the upgrade. I will update when it comes in, Allen, do the same if you are able to update be I do.


Reply
dlovely
Posts: 3167
(@dlovely)
Famed Member
Joined: 17 years ago

Prop Plug can be found direct from Parallax (The MFG) at this link: https://www.parallax.com/product/32201

They do not offer a bulk rate so I have to order them at that price to post them in the store. It only makes sense if you are ordering other stuff so I just offer them during pre-sales to save a few dollars shipping from ordering two places.


Reply
Posts: 59
Topic starter
(@arange98)
Trusted Member
Joined: 12 years ago
boyelroy11 wrote:You'll need a prop plug to upgrade the firmware. I ran into this last season, and David worked through it, providing me beta firmware versions to find which worked with the newer pixels.

http://www.diyledexpress.com/index.php?main_page=product_info&cPath=22&products_id=161

I see they are sold out, but it is available elsewhere online.

Bruce

thx. Fortunately I picked one up a while back. Now I just need to find it. LOL.


Reply
Posts: 430
(@danonj)
Reputable Member
Joined: 18 years ago

Same issues here. Can someone please point me to the link for the new firmware? Thanks


Reply
boyelroy11
Posts: 757
(@boyelroy11)
Prominent Member
Joined: 17 years ago
Reply
Page 1 / 4
Share: