Having finished a major remodel of our house and some major maintenance on the deck, I need to add some lighting back to it (I removed the ancient low-voltage lights which were in bad shape and gave them away). LED strips under the railing caps and on the roof eave would provide a nice glow and give more than enough light. Color is essential (to me) and some basic effects would provide a nice "wow" factor (but not "blinky flashy" type shows).
I could achieve this with "dumb" RGB strips (and save a little bit of money), but in anticipation of some other future projects (one of which might be a small but nice Christmas "blinky flashy" show) I'd like to jump straight in to pixels.
Having been on this forum for quite a few months, I'm getting more comfortable with the technology and terms every day (but I still have questions). In particular, being a software engineer with a lot of network experience, everything from the pixel controller through the LAN into the "show computer" is very comfortable for me. I've done basic low-voltage yard lighting which came out very well, so have a little bit of experience there. The pixels, connectors and wiring, and general installation with this type of technology is where I'm less experienced.
First a terminology question - the newer 2811/2812 strips mention "30 LED/M" or "60 LED/M" (or similar density). I'm assuming this means 30 or 60 pixels per M, correct? The shift from "3 LEDs per pixel" vs "1 LED per pixel" has occurred, or more accurately it's "1 IC per pixel", which (deep down internally) has 3 LEDs somewhere - correct?
I'm looking at four 5M, 5V strips of 30 LED / M density (2811 IC, 5050 LEDs). This should provide more than enough light for evening deck activities, and nicely outline the deck (not 100%, as there is over 90 feet of deck railing and overhanging eave, but close).
The E6804 seems like an excellent controller fit for this configuration. I already posted a question in the vendors subforum about details on the "Pixel System 2" from SanDevices, including availability dates. However, since at least one of the strips will need to be cut into two or three pieces to match the deck rail outline (there is an octagonal area that looks like it was designed for a hot tub, specially with the massive supports underneath), I'm assuming the "no solder connectors" used in the Pixel System 1 will not completely eliminate some needed soldering (which is ok for me).
I haven't calculated needed wattage - the PS 1 has a 350 watt supply, and if the PS 2 has a similar wattage I would hope that's enough.
Controller / power supply housing, data line and power distribution and injection suggestions are welcome - since the deck is attached to the house I could mount the controller and power supply inside, but some of the power and data lines would be close to 40 feet. I could house them (in a waterproof enclosure) right in the middle of the deck underneath on a support post (this is in effect a second story deck), if that makes more sense, with the data and power lines in a "star" type of configuration, for the minimum length of runs (everything would be within 20 feet or less, and with careful placement I would guess none of the connections would be farther than 10 feet away).
The strips will not be taken down seasonally, so waterproofing for many years of Seattle weather is essential. The strip mounting will also need to be unobtrusive and "professional looking" or the spouse may decide to do her own lighting. Suggestions for strip channels, waterproofing (I've already ordered some electrically neutral silicone) and general installation tips are greatly appreciated.
Show computer - this will definitely not be a traditional type computer. For what I have envisioned, even one of the low-cost "RGB strip controllers" has enough variety and functionality, but I'm assuming none of them output E1.31 over a Cat 5 cable (or if they do, or there's an easy converter cable, that might be fine). So maybe a Raspberry Pi (or similar) with a small "embedded" style sequencer would be enough (e.g. the "Falcon Pi Player" being discussed in the Development subforum). Actually, thinking about it, something that also synchronizes with audio would be nice (I haven't mounted any outdoor speakers, but that wouldn't be hard).
Sequences I'm envisioning so far are something like:
-- Gradual changes from one color to another, possibly gradient or a slow "chase" around the outline
-- Seasonally appropriate colors
-- Simple white (warm white) when colors are not desired
-- Occasional random "pixel on or different color", kind of a slow twinkling effect
-- Hmm - with a 13 yo, maybe also have something more stimulating and wild for when he has friends over
I'm sure there will be good suggestions, and feel free to tell me if I'm doing anything stupid.
🙂
Cliff
Interesting timing of this post.
I'm working toward the very same sort of project and in fact will be mocking up half my deck during the upcoming US holiday. I concluded that 12V pixels (3Leds/control) would work well, not need as much current as the 5V variety and not need the exacting pixel control due to down-wash lighting. However I will be mocking up 12 meters of 5V (60/M) and 15 meters of 12V to verify. I have E682 controllers as well as the 6804 (which might be the better choice).
Connectivity will be interesting yet somewhat simple. After a data run of 15-20' it looks like a null pixel data signal booster would be needed (basically a cable interconnect with a bump or two in the middle). Either way consideration must be for the amount of amperage needed and current capability of the pixel strips. Power Injection will _certainly_ be needed.
I've been working toward some designs that will carry the pixel strips along with extra wire pair for extending the power for injection. All of this will be in the same pixel mounting frame which will be waterproof, with waterproof connectors on each segment. These frames will be in different lengths, probably to nearest foot, perhaps six inch, from 3' to 8'.
A challenge is to create pockets in the deck posts to contain and / or route the wires between the railing segments, as well as provide down channels that hide the wire, yet remain accessible for service.
I agree with the Pixel controller thoughts, however I'm looking from a slightly different perspective. My controller will be wireless, can operate independent without a PC for connection. However, will still be able to use a PC to be able to download new sequences.
And I'm working on an interesting kicker to the whole setup that I think will be really cool, but can't yet detail.
I too think this will make the deck a really nice place to be and to see for all seasons.
Great! You're significantly ahead of me, specially with some mock up tests. I'm looking forward to reading about it (and in particular the mounting frame design).
If 12V strips make more sense (due to less current) for the needed amount of light (which shouldn't be much), that's good to know.
I figured that power injection would be needed, but didn't consider data signal propagation issues.
Deck post channels - all of our railings are wood, so theoretically a channel could be "routed" into it (not sure how this would be done, though). But in our case, as long as the cable is unobtrusive in appearance (black, I would assume), there are places I can attach that won't be too noticeable. In particular, the yard is so far below the deck that putting cables on the outside of the railings and posts would work for us, and very people would notice or care (we already have some irrigation tubes that go from below the deck to various planters).
If we ever switch to thinner metal railings, it would be harder to disguise (which we've talked about, since 3/4 of the cleaning maintenance time on the three decks we have - one big that I'm posting about, two small ones - is for the railings).
"My controller will be wireless, can operate independent without a PC for connection. However, will still be able to use a PC to be able to download new sequences."
Yes, I was thinking along those lines, too, just not in this much detail. I'll run some thoughts / general desires by you in later posts.
Thanks, Roterhead!
Cliff
I'm especially looking forward to hearing about the physical mounting / wiring approaches each of you takes.
Extra wiring for power injection is another area of interest; if your power supply is at one end of a long string, you could still need some fairly heavy gauge feed wire. I'm thinking to use distributed waterproof supplies (ie: still need AC distribution, but voltage drop is not a problem).
I recommend using distributed power for the lighting. The power supplies are about $10 a piece and they are waterproof.
http://www.powergatellc.com/mean-well-lpv-20-power-supply.html
Interesting, Ronp and Zeph! I was (naively?) thinking one power supply and distributing the low voltage drops. In your recommendation the AC main is distributed (much less voltage drop) to small AC / DC power supplies, and short runs to the strips.
I'll read up a bit here (and other appropriate places) about how people are distributing AC power and ask some (hopefully intelligent) questions about it. Obviously if I had enough outdoor receptacles that would be a 1-1 mapping of receptacles to PS. And I might - underneath the deck there is a four plug receptacle, although two are taken up (garden lights, irrigation system), and I think there's at least one more receptacle available underneath (not sure if it's 2 or 4 plug). And there's at least a double receptacle at deck level, although it would be nice to keep that one for deck needs. But I'm assuming I'd rather distribute from one (or maybe two) outdoor receptacles.
Then it's just a matter of data signal hookup and propagation.
Cliff
Data shouldn't become a problem as each 2811 regenerates the data signal before passing it on. I have 2811's over 30' from my controller with no problems. I like the e682 controller idea, but on my deck I use Ray's super simple controller http://www.aliexpress.com/store/product/DC12V-input-WS2811-LED-smart-pixel-controller-for-testing-max-100pixels-controlled/701799_652082488.html it does a nice job on a 5m strip. Ebay has them cheaper if you only want one or two http://www.ebay.com/itm/DC12V-Mini-Controller-For-5050-SMD-RGB-WS2811-IC-Dream-Color-LED-Strip-Module-/151031253713?pt=US_Weather_Meters&hash=item232a2a0ad1 Give it a try, even if you don't use it for your deck, it makes a great test controller to test 2811 strips. Hope this helps:
John
Thanks, John - I hadn't seen these simple controllers before. I'll definitely get one (or some) - like you said, even if not used for "production" controllers, they are great for simple testing.
Both have 2 wires in for power and three wires out for the 12v 2811 led's


