Couple problems wit...
 
Notifications
Clear all

Couple problems with my pixels not functioning correctly. One string not responding?

8 Posts
4 Users
0 Reactions
2,357 Views
Robo
Posts: 1494
 Robo
Topic starter
(@robo)
Noble Member
Joined: 14 years ago
[#25754]

Ok I finally got my mega tree pixelized with 12v ws2801. I have it working fine with xlights via e684. But I have one stringer of 50 pixels not responding as it should. I ran the e683 test and all other strings work fine red/ blue, green, etc... Its just one string of 50 ct, they do light but only about 40 of them light up. The other 10 are totally out. And the ones that do like up are the wrong color and non responsive. I've tried swapping the pigtail with another string to see if it changes, BUt the string still wont light up properly. Just a bunch of pastel colors that occaionally flicker. Not responsive at all.

Also the other problem I'm having is that two other pixels, not in the dead pixel string, turn yellow when I use white. Any other color its fine but once I use white it turn to yellow.

Finally do you thing that my 800 pixel tree with a run of 25 ft needs more then 2 350watt PS? Would this be an issue.

If you have any insight on how to troubleshoot this please help me out. Thanks Rob


7 Replies
Posts: 6728
(@p-short)
Illustrious Member
Joined: 19 years ago
Robo wrote:Ok I finally got my mega tree pixelized with 12v ws2801. I have it working fine with xlights via e684. But I have one stringer of 50 pixels not responding as it should. I ran the e683 test and all other strings work fine red/ blue, green, etc... Its just one string of 50 ct, they do light but only about 40 of them light up. The other 10 are totally out. And the ones that do like up are the wrong color and non responsive. I've tried swapping the pigtail with another string to see if it changes, BUt the string still wont light up properly. Just a bunch of pastel colors that occaionally flicker. Not responsive at all.

Also the other problem I'm having is that two other pixels, not in the dead pixel string, turn yellow when I use white. Any other color its fine but once I use white it turn to yellow.

Finally do you thing that my 800 pixel tree with a run of 25 ft needs more then 2 350watt PS? Would this be an issue.

If you have any insight on how to troubleshoot this please help me out. Thanks Rob

It's hard to say if those supplies are enough, or not. Some 12V pixels draw around 10 mA per pixel, others take 20 mA. In the former case you would need to supply about 24A max, 48A in the latter case. What are the specs for your power supplies?


Reply
Posts: 1249
(@jstjohnz)
Noble Member
Joined: 17 years ago

If I understand correctly, the problem stays with one specific pixel string, even if you attach to a different connector on the E6804? If that is the case then it sure sounds like that string is bad. You may want to double-check the wiring to that string.

Re the yellow pixels, red, green, and blue work OK independently, but white does not? That's a bit strange. What about say half-intensity white? That sounds like a faulty pixel to me.

One 350W power supply is probably enough, 2 is plenty. What is the 25 foot run? Power supply to controller or controller to pixels? If you want your power supply 25 feet away from the controller you should run at least 2 sets of 12 gauge wire, maybe even 10 gauge, from the power supply to the controller. It's usually best to keep controller and power supply close together.

If you're talking about 25 feet from controller to pixels, that could be an issue as well. If you are running that much cable that could be the source of some the pixel issues you are seeing. That wire should be at least 18 gauge. If that's your setup now, I would try shortening the run to the problem string as a test to see if that helps.


Reply
Robo
Posts: 1494
 Robo
Topic starter
(@robo)
Noble Member
Joined: 14 years ago

heres the spec on the power supplies
http://www.HolidayCoro.com/350w-Dual-Output-Power-Supply-p/49.htm

jst, You are correct. By switching outputs on the e682 still the same results on that one 50 ct string. Is the entire string bad or can I troubleshoot which one is bad and cut that one out? Thats about $50 worth of pixels.

The yellow 2 pixels work fine with any color except white.

The 25ft run is the total length of each string from controller to the last pixel. I think thats a pretty short run since the controller and PS are mounted right on the tree pole.


Reply
Posts: 11
(@kselswick)
Active Member
Joined: 14 years ago

If the pixels were bought from diyledexpress there was a problem from the manufacturer that causes this. Email Todd or contact me and I can explain.

Kevin


Reply
Page 1 / 2
Share: