I am using 12V 2811 pixels, 800 of them. All 16 ports on my E682 are planned out. All are put up, some are wired up now.
What I would like to know if what everyone is using for wiring between the controller and pixels and where did you get it?
I have CAT5e up the waazoo but it of course is very thin. My furthest pixels start some 35' away from the controller. I have a null pixel about halfway in these runs, data is getting to them and they are working except slight flickering on full white which is due to trying to power them from a long cat5 run i'm assuming. My longest actual pixel string is 109, shortest being 34.
Sure I could inject some power at the ends but again, long cat5 runs for this probably wouldn't be that effective. I was looking at hardware stores for wire but can only find single wire spools except for romex which was an idea but not very cost effective as a 25' is $10. For that price i'd put up with the flicker on white as all other colors are nice and solid.
Again, just wanted to see what everyone else has found and where.
Thanks,
Steve
Most have settled on 4 core 18ga Alarm wire.
I use a mixture or flat 4 core cable from RAY (bought on 1st purchase but would not recommend as it is too thin) and 4 core alarm cable.
Usually you can find 500' reels for about 40$ or $50.
James70818 has a post about this retailer: http://doityourselfchristmas.com/forums/showthread.php?34082-Diyc-Respected-vendors&p=337519#post337519
I use Cable-Zilla, but James price is better and he seems to like the quality so next order I may try his reseller.
I started using the 4 wire Security Wire Burglar Alarm 22/4 Cable 500FT Stranded White 500' Speaker Cable (actually bought some last night). You can get it on Ebay for 26-30 bucks. I used it for 20 foot runs last year with no problem. You can also get the 18ga wire for approx 50 bucks as DrNeutron states.
On full white you can just get enough voltage drop that you will have to inject at the end of the pixels or someplace in the middle anyways.
I have the porcupine ball and it was ok with single colors out to 255 pixels off an e682 that uses 45' of the flat 4 wire mentioned above to bring data back down the spikes to the next connector. To resolve the issue I split the feed and put power about in the middle going both up and down. You can run another cat 5 to the end from the same port on the E682, just don't connect the data at the end to bring the voltage back up.
For data transfer, you should you wire that has a waterproof jacket. Not INDOOR wiring. For dumb RGB strips it is not as much of an issue.. but for data it can be. Make sure whatever size you use accounts for voltage drop.
I recommend you don't use solid wire for connection to strips.. You can, but I wouldn't..
plasmadrive wrote:
I recommend you don't use solid wire for connection to strips.. You can, but I wouldn't..
+1. For my matrix this year I used thermostat wire which is solid core. It is nice and sturdy,but a pain to work with. If doing it again, I definitely would go with stranded if possible.
DrNeutron wrote:Most have settled on 4 core 18ga Alarm wire.
I use a mixture or flat 4 core cable from RAY (bought on 1st purchase but would not recommend as it is too thin) and 4 core alarm cable.
Usually you can find 500' reels for about 40$ or $50.
James70818 has a post about this retailer: http://doityourselfchristmas.com/forums/showthread.php?34082-Diyc-Respected-vendors&p=337519#post337519
I use Cable-Zilla, but James price is better and he seems to like the quality so next order I may try his reseller.
So what do you use the other two wires for? Or do you double them up for power?
Travis
Arctic8000 wrote:So what do you use the other two wires for? Or do you double them up for power?Travis
There won't be two extra wires left - you need at least 3 for pixels and 4 four some like 2801 and dumb pixels.
There would only be one wire "left over" if using WS2811, Ws2801 is 4 wire....
I use it for a variety of uses...
For my Dumb RGB I use all 4 of course.
For 3 wire 2811 pixels you could use it for power injection or double it up if your run isn't too long.
The flat 4 wire from Ray, I double up the +12v as it is very thin, but I am only going a short distance.
As per Plasma's suggestion when he made the Plasmicles , I started using DC to DC converters and use laptop power supplies. As my display grows, I will house them in enclosures and use them for power injection when necessary. I'll look at using that 4th wire for injection at some point...... The beauty of using DC to DC converters is that you can standardize on the 18ga wire and not have to get anything thicker to accomplish your power needs, just need to plan it out.
budude wrote:There won't be two extra wires left - you need at least 3 for pixels and 4 four some like 2801 and dumb pixels.
DrNeutron wrote:There would only be one wire "left over" if using WS2811, Ws2801 is 4 wire....
I use it for a variety of uses...
For my Dumb RGB I use all 4 of course.
For 3 wire 2811 pixels you could use it for power injection or double it up if your run isn't too long.
The flat 4 wire from Ray, I double up the +12v as it is very thin, but I am only going a short distance.
As per Plasma's suggestion when he made the Plasmicles , I started using DC to DC converters and use laptop power supplies. As my display grows, I will house them in enclosures and use them for power injection when necessary. I'll look at using that 4th wire for injection at some point...... The beauty of using DC to DC converters is that you can standardize on the 18ga wire and not have to get anything thicker to accomplish your power needs, just need to plan it out.
For some reason I thought this thread was about just power injection. Now that I actually read it I see why now. oops but thanks for clarifying.
Travis
