Cable distance betw...
 
Notifications
Clear all

Cable distance between controller and strip light

10 Posts
3 Users
0 Reactions
3,488 Views
Posts: 6
 txx
Topic starter
(@txx)
Active Member
Joined: 10 years ago
[#44737]

I was wondering what the general distance limit is for cable between a controller and a strip light.
For example:
16 output alphapix controller
30led/meter 10 pixel per meter strip light

Potential setup:
1 strip light for each output
1 350w power supply per bank
pigtails coming out of the strip light and the controller
18 gauge extension cable with pigtails on either end connected to the pigtails from the strip light and controller.

I'm doing some research and measurements, and if I needed a 60 foot distance between the controller and the farthest strip light, would that require a null pixel and/or power injection? From what I've seen, lengths greater than 20-25 feet generally requires some power injection (is that true?).

An additional question: If I have 8 strip lights connected to 8 outputs on one bank of the controller, all greater than 25 feet, and they do require power injection, is it better to place the power supply for that bank with the controller, and an additional power supply to power inject by the strips? Or only run data from the controller to those lights and place the power supply closer to the lights?

Any advice is appreciated -- I'm only researching right now, and if I need to clarify or add info, just let me know.

Thank you


9 Replies
TazChaLet
Posts: 3042
(@tazchalet)
Famed Member
Joined: 13 years ago

(lengths greater than 20-25 feet generally requires some power injection) it isn't the power that is problem mainly it is the data signal that at longer length have problems null pixels help since they take the data and resend it out some people have used rj45 cable just 2 of the 8 wires 1 for data and 1 for gnd and got some good distance not sure how far you really can go that way


Reply
Posts: 6
 txx
Topic starter
(@txx)
Active Member
Joined: 10 years ago

Thanks for the reply

I've seen some suggestions about using rj45 or cat5 cable and getting long distances like that. I'll have to research more about them to get a better understanding, but it's good to know that it is an option.

Are long distances possible with 3 core 18 gauge wire? (even if it needs power injection and null pixels)


Reply
TazChaLet
Posts: 3042
(@tazchalet)
Famed Member
Joined: 13 years ago

you can do longer distance with 3wire if you add nulls and power inject if needed the power injection would be closer to the prop so the distance really wouldnt be long for power but data would need the nulls to get signal down the long line you can add more than 1 null pixel along a long line to repeat the signal say every15-20' till you reach the prop

txx wrote:Thanks for the reply

I've seen some suggestions about using rj45 or cat5 cable and getting long distances like that. I'll have to research more about them to get a better understanding, but it's good to know that it is an option.

Are long distances possible with 3 core 18 gauge wire? (even if it needs power injection and null pixels)


Reply
Posts: 6
 txx
Topic starter
(@txx)
Active Member
Joined: 10 years ago

Thank you again for the advice and helping me out. I figured I might have to do one or the other at those distances, especially just to be safe since they are long distances from the controller.

Just a quick question -- for those lights that are farther, like if I had 8 strips greater than 25 feet from the controller, should I have power supplying them through the controller or just closer to the lights, or both though the controller and by the lights?

Also if anyone else reads this and has additional input or suggestions, that definitely helps as well -- the more information the better to help me figure this out since I'm still just doing a bunch of research.


Reply
Page 1 / 2
Share: