OK, so I am paranoid, as I am sure most of us are.
Ive not used pixels yet. However, I am taking the plunge.
I know if a single pixel goes bad, I can cut it out an replace it, so having a few on hand would be good.
What I don't know is... can I screw up and blow up an entire string.... could an entire string bite the dust?
Should I be keeping multiple full extra strings on hand?
I mean sure a surge could blow everything I had hooked up to an e682, and I couldn't recover from that no matter what, so lets not count that.
What I really want to know is.... how many pixels should I keep in my back pocket for backups? Is 1 extra string sufficient?
Thoughts????
Thanks for anyones input here. I don't want to be wasteful, but at the same time I want to be covered.
your not very likely to blow more than the first 1 if you short circut the input . 5 or 6 spares is fine .
if your cutting strip into smaller bits to create custom elements , that is a different story all together if you get water ingress etc .
But for things like a mega tree a couple of extra string is nice to have for ez swapping if you get a bad pixel that annoys you .
trying to repair 1 pixel that is 2/3 the way up a mega tree string in the winter weather would be no fun
Hi everyone. I'm in the same boat, no Pixels yet.
I am planning to add 2 controllers this year (2014) though and have a simular question.
After looking at the wiki:
--> http://www.doityourselfchristmas.com/wiki/index.php?title=RGB_Lighting<--
There are always a few lights that go out every year on my standard display so now I am wondering about Pixel Repairs.
(1) How many elements can I cut out if I need to?
(2) Does this not screw up the controller?
(3) If my string of lights (1--2--3--4--5--6--7--8--9--10.....) has element #5 go bad and I cut it out and solder in a new element
how does the controller know #5 is still #5 and at the same location, I thought they were "chipped" to tell the controller where and what they are.
If some one has field experience may I suggest an update to the Wiki adding a section about Pixel Repair.
Thanks to all.
Bjlled wrote:OK, so I am paranoid, as I am sure most of us are.
Ive not used pixels yet. However, I am taking the plunge.
I know if a single pixel goes bad, I can cut it out an replace it, so having a few on hand would be good.
What I don't know is... can I screw up and blow up an entire string.... could an entire string bite the dust?
Should I be keeping multiple full extra strings on hand?
I mean sure a surge could blow everything I had hooked up to an e682, and I couldn't recover from that no matter what, so lets not count that.
What I really want to know is.... how many pixels should I keep in my back pocket for backups? Is 1 extra string sufficient?
Thoughts????
Thanks for anyones input here. I don't want to be wasteful, but at the same time I want to be covered.
Sparkey wrote:Hi everyone. I'm in the same boat, no Pixels yet.
I am planning to add 2 controllers this year (2014) though and have a simular question.
After looking at the wiki:
--> http://www.doityourselfchristmas.com/wiki/index.php?title=RGB_Lighting<--
There are always a few lights that go out every year on my standard display so now I am wondering about Pixel Repairs.
(1) How many elements can I cut out if I need to? as many as you want
(2) Does this not screw up the controller? no it will not screw upp the controller
(3) If my string of lights (1--2--3--4--5--6--7--8--9--10.....) has element #5 go bad and I cut it out and solder in a new element yes you can
how does the controller know #5 is still #5 and at the same location, I thought they were "chipped" to tell the controller where and what they are. all the pixels are controlled with a data cable or line the controller will know it is #5If some one has field experience may I suggest an update to the Wiki adding a section about Pixel Repair.
Thanks to all.
I have 4 strings on hand in case something goes screwy, but that is just me.
Sparkey wrote:Hi everyone. I'm in the same boat, no Pixels yet.
I am planning to add 2 controllers this year (2014) though and have a simular question.
After looking at the wiki:
--> http://www.doityourselfchristmas.com/wiki/index.php?title=RGB_Lighting<--
There are always a few lights that go out every year on my standard display so now I am wondering about Pixel Repairs.
(1) How many elements can I cut out if I need to?
As many as you need to.
(2) Does this not screw up the controller?
Why would it? You power off the controller to make repairs, then power it back on.
(3) If my string of lights (1--2--3--4--5--6--7--8--9--10.....) has element #5 go bad and I cut it out and solder in a new element
how does the controller know #5 is still #5 and at the same location, I thought they were "chipped" to tell the controller where and what they are.If some one has field experience may I suggest an update to the Wiki adding a section about Pixel Repair.
Thanks to all.
They are addressed in a serial line, not with a physical set address. So, the first pixel in line gets data for pixel 1, the second gets data for pixel 2, etc. There is no specific settings. This makes things easy.
