ANOTHER pixel fire!
 
Notifications
Clear all

ANOTHER pixel fire!

26 Posts
10 Users
0 Reactions
5,221 Views
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago
[#57330]

Last night I did a test run of my display. I decided to watch the entire show to catch any sequencing issues. After running 2 hours my eye was drawn to an odd sight on a 6 foot mini tree (500 pixels). I'd never seen a pixel or effect like it so as I watched from afar I noticed what appeared to be falling lights (like an icicle) only it was 'falling' from the top. At first it was 1 trail then 2....Then I noticed the 'light' at the top of the tree getting bigger. Then it dawned on me. FIRE!!!!!

By the time I ran the 250 feet to get to it the top of the tree was aflame with the mounting strips being on fire and dropping flaming drops to the ground. I ripped off my shirt and extinguished the fire as I didn't want to take time to run in the house and get an extinguisher.

It took out 8 out of 20 strings.

I have run these pixels for 4 seasons and while they did have issues with failure after a rain there was no hint of overheating before on this batch of pixel. That being said, another batch, from the same 'over the pond' supplier did have 1 pixel catch fire a couple of seasons back. That string was on a prop (Rosa Wreath) on the house. I replaced ALL the pixels (reglulated) that were in props (wreaths and snowflakes) on the house with pixels (resistor) from another supplier (Tom). These pixels have had some water failures but no overheating.

I moved all the old pixels from a couple of seasons ago onto props in the yard. The pixels on the flaming mini tree weren't of the same batch but WERE from the same supplier. I won't mention the name of that supplier but they weren't from Tom. Nuff said.

All the pixels on the flaming mini tree WERE fused yet that didn't matter in the least. But once the fire burned through the pixel wires and they became exposed THEN they shorted by touching 12v and gnd wires which DID take out the fuses. I guess that was good since it took away the voltage and prevented it from doing even MORE damage.

After using standard (120 volts) incads and LEDs for 50 years I NEVER had a fire! Now I've had 2 from 12 volt 'Regulated' pixels in the past couple of years. NOT GOOD!!!!!

I have thousands of these fire prone pixels out in the yard from the past few seasons that I will need to replace. But the dilemma is getting replacements in time for THIS season. I have spare resistor pixels but not nearly enough.

This SUCKS!!!!!! :angry:


25 Replies
MartinMueller2003
Posts: 7613
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

5v pixels. IMO, no element doing any special heat disposition. Lower chance of fire.


Reply
rstehle
Posts: 4348
(@rstehle)
Illustrious Member
Joined: 19 years ago

Ouch, you have certainly had your share of Pixel problems. You might check on the xlights support page on FB. I think there are vendors there that have Pixels in stock.


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Since you've used these pixels for several years, I'll guess that over that time, *some* moisture has sneaked into them and has caused some of the short problems that you apparently are seeing. Pixels are still a relatively new product and as such, I don't believe any vendors can successfully advertise that any are 100% waterproof. If air can reach the interior part of any electronics, it is not 100% waterproof because air can carry humidity, and that humidity will condense when the temperature drops. It's the physics of nature. I have tested pixels and pixel strips that supposedly were completely sealed inside non-conductive gel by simply setting them outside, attached to a board and not even powered on. I would check them every spring. All of them worked before I put them outside but after 4 years, none of them worked anymore. It was a good lesson to learn.


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago
dirknerkle wrote:All of them worked before I put them outside but after 4 years, none of them worked anymore. It was a good lesson to learn.

An expensive one as well me thinks.

When you're sitting on over 100K pixels the idea of replacing all of them every 4 years brings up some decision points that are painful either way you go. Not to mention it seriously limits how much you can expand the display. I realize any electronic component has a definite shelf life but the actual amount of time pixels operate, given the nature of and season length, is not that extreme.


Reply
Page 1 / 6
Share: