Firework Light Simu...
 
Notifications
Clear all

Firework Light Simulation

117 Posts
41 Users
0 Reactions
121.9 K Views
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago
jrock64 wrote:The shortest cut on most rope light is 18 inches.
...

I bought the blue rope light for $30, the other colors are on hand from other projects.
I bought a $2 package of finish nails and am using leftover wire from when I previously remanufactured mini strands to make the rope light power connectors, already half done.
$150 for strobes from CDI, but am already rethinking this, if a regular c9 that was faded out would look better.
I am guessing about $100 for all the steel and pipe for a new pole.
8 channels computer controlled lighting controller, I think i have a few of those somewhere.

No where near $1800 and I will have DIYed it.
That's more than half the fun.

Joel

With all ue respect, what you are building will not be anything near the $1800 one I saw. The 18 footer would be $1200 and it had 40 spokes on it. I think its great and if we can figure it out, I definitely want to DIY it, but there are other economies to consider. There are those who are not up to tackling a project of this size. (possibly including me). In all likelyhood, we are looking to purchase just the top piece with the spokes and lights, but without main pole and controller.

To be fair, for comparison, your cost estimates should NOT exclude the cost of materials you have laying around. I have enough parts laying around to build a Ren 24, but that wouldn't make it free 🙂 There will certainly be lost dollars investigating and trying different products. I'm ok with that, but you certainly need to figure it in. When I did some rough calculations, I was figuring 300-400 budget plus controllers. More if I do Fiberglass spokes. If I'm going to do it, I'm going to make it so I can do a lot more than just a firework look with it. That means a lot more than 8 Channels. Conservatively, I was figuring 64 Channels.

All that said, I'm pulling for ya! I would love a good reference implementation. I'm not an engineer, I'm an Implementer 🙂

btw... do you think the 3/16 rod will be stiff enough? I assume you are talking Fiberglass?


Reply
Posts: 1065
(@olingerjccj)
Noble Member
Joined: 17 years ago

I am laying out my firework. No one will be able to view this from behind, so how do you think 2d spokes would look. I am planning on using 16ft so like 20 spokes.

John


Reply
Posts: 67
(@bhays)
Trusted Member
Joined: 18 years ago

I am new to fiberglass rod... I found this site which sells fiberglass rod and tube far less expensively than the driveway markers.

http://www.mgs4u.com/fiberglass-tube-rod.htm#pricelist

This makes sense seeing as the markers have added material, reflectors, etc. and all we need for this project is simple rods, plus they have all lengths.

Is anyone here with a radio/ham background who might know more about this stuff? Does this look like it would work for our project?


Reply
Posts: 67
(@bhays)
Trusted Member
Joined: 18 years ago

I am waiting for pricing from China on an 8 meter and 6 meter unit shipped to my nearest seaport which is Cincinnati. These are incandescent without the pole and have 60 spokes each. What really makes these impressive to me is the very large size and number of spokes and when you start pricing materials, I really don't see any way to do it for less than $500-$600 each...

I will report back as soon as I get a price..


Reply
Posts: 494
(@tlorek)
Honorable Member
Joined: 18 years ago

From a basic construction standpoint, I can see how this would seem simple at first:

- Get some steel or fiberglass rods (40-60)
- Cut them to various lengths (in 18" increments, assuming rope light spacing)
- Buy 4-5 spools of different color ropelights
- Cut ropelight in 18" lengths and attach power cords to them
- Tie wrap to rods
- Fabricate a center hub with curved steel pieces (~10) as vertical attachment points for the rods
- Fabricate an attachment method for the rods to the attachment points

From my thinking, so far this isn't *too* bad to fabricate. The difficulty comes in here:

- Make a simple attachment method for all of the electrical connections. 🙁

If you have 60 rods, each with 5 colors (plus an end C-9 or strobe), you've got 60 individual connections you need to bring all together into one (x 6 for each segment of each rod). Now if I remember, incandescent rope light is ~5w (?) per foot. If you've got 90' @ 5 watts, then you've got 3.75 amps per channel. OK, then instead of 6 channels, bump it up to 12 channels to get the amps per channel down. Think of the maze of wires. Now you could fabricate boards and purchase headers and connectors to simplify things a bit, but you're talking about 12 boards with 31 connectors going into each (you need 1 for power). Then you need enclosures, and everything needs to fit into the head of the firework. :-(:-?

Someone smarter than me is gonna need to figure that part out!!!!


Reply
Posts: 67
(@bhays)
Trusted Member
Joined: 18 years ago

Yep, I was going to go with Molex connectors. The cost isn't too bad until you start purchasing 300 ropelight power connectors and an equal number of molex connectors for the spokes..

Whichever of us breaks down and buys one first will have to provide detailed info and pics for everyone else who wants to DIY it..


Reply
Posts: 221
(@stanward)
Estimable Member
Joined: 18 years ago

Is there a port in California that can accept the Chinese goods? Maybe someone in California is willing to purchase one of these units to "disect" for us as you stated (bhays)?

Please let me know if you can find a cost for the unit.


Reply
Posts: 1065
(@olingerjccj)
Noble Member
Joined: 17 years ago

Any ideas how to attach a big ball to the pole?

Thanks
John


Reply
Posts: 67
(@bhays)
Trusted Member
Joined: 18 years ago
olingerjccj wrote:Any ideas how to attach a big ball to the pole?

Thanks
John

My thought would be to weld a piece of pipe that will slip tightly over the pole to the bottom of the ball.


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago
stanward wrote:Is there a port in California that can accept the Chinese goods? Maybe someone in California is willing to purchase one of these units to "disect" for us as you stated (bhays)?

Please let me know if you can find a cost for the unit.

For those in HI, I'm assuming we need to find somone who will sell it without the main Pole. It would be pretty stupid to pay 200 to ship a $200-300 pole.

I really wasn't counting on another large project this year, but I am very interested in the fireworks ever since someone else mentioned it last year. Now, you guys have really gotten me going.

I have traded Voicemails with the LED PalmTree / Fireworks guy in Northern Cincinnati. Hopefully we'll hook up soon and I get really figure out what the minimal cost would be to purchase complete units or partials in bulk.

Kelly


Reply
Page 7 / 12
Share: