I messed up
 
Notifications
Clear all

I messed up

28 Posts
6 Users
0 Reactions
8,328 Views
wilmar
Posts: 2115
Topic starter
(@wilmar)
Noble Member
Joined: 8 years ago
[#52225]

Can someone that knows about pops power fan out boards help as I soldered the main power lugs on the opposite side of the board . Will it still work if I build on opposite side or will it somehow reverse some stuff ? Lots of solder not sure if I can get em out without some suction thingy .

Sent from my iPhone using Tapatalk


27 Replies
wilmar
Posts: 2115
Topic starter
(@wilmar)
Noble Member
Joined: 8 years ago

I thing if I finish build correctly and just main lugs are upside down as long as + and - are connected properly everything should be good ?

Sent from my iPhone using Tapatalk


Reply
wilmar
Posts: 2115
Topic starter
(@wilmar)
Noble Member
Joined: 8 years ago

Also I don’t see these pins on any of the photos were they switched out for the green screw lugs I’m thinking ?

Sent from my iPhone using Tapatalk


Reply
Posts: 376
(@k-state-fan)
Reputable Member
Joined: 16 years ago

unsolder them and put them on the correct side


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago
wilmar wrote:Also I don’t see these pins on any of the photos were they switched out for the green screw lugs I’m thinking ?

Sent from my iPhone using Tapatalk

I use these:
https://www.ebay.com/itm/50-SETS-JST-XH-2-54MM-2Pin-Male-Female-Connector-plug-with-Wires-Cables/263879405198?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

This is where you use the pins where you see I used the JST connector next to fuse 5.

JST

Reply
wilmar
Posts: 2115
Topic starter
(@wilmar)
Noble Member
Joined: 8 years ago
pmiller wrote:This is where you use the pins where you see I used the JST connector next to fuse 5.

Figured jus wanna be sure trying not to mess up anymore than I already have

Sent from my iPhone using Tapatalk


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

I agree with K-state Fan. Unsolder it. If you can't, send it to me. I have a desoldering station that will suck it right up.

Sent from my SM-T710 using Tapatalk


Reply
wilmar
Posts: 2115
Topic starter
(@wilmar)
Noble Member
Joined: 8 years ago
pmiller wrote:I agree with K-state Fan. Unsolder it. If you can't, send it to me. I have a desoldering station that will suck it right up.

Sent from my SM-T710 using Tapatalk

May take you up on that if your serious

Sent from my iPhone using Tapatalk


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago
wilmar wrote:May take you up on that if your serious

Sent from my iPhone using Tapatalk

Sure I'm serious. Msg me I'll give you the address. Send it all and I'll solder everything for you. I'll even add the JST connectors if you want. I have a lot of them. Better yet. Give me your address and I'll send you one of mine. When you receive it, then send me yours as a replacement.

Sent from my SM-T710 using Tapatalk


Reply
Page 1 / 3
Share: