HolidaCoro
 
Notifications
Clear all

HolidaCoro

17 Posts
5 Users
0 Reactions
4,957 Views
Posts: 44
Topic starter
(@theycalmegriswal)
Trusted Member
Joined: 10 years ago
[#42615]

I am trying to figure out how to control my dumb rgb's from a Alphapix controller (RS485) to 2 dumb 30 channel controllers. Question is, I have setup 18 universes in nutcracker, 17 and 18 are for the two dumb controllers (10rgb channels). How do I get nutcracker to show me each controllers 10 channels in these universes?

Oh and yes, I am new to this hobby.

Thank you.


16 Replies
TazChaLet
Posts: 3042
(@tazchalet)
Famed Member
Joined: 13 years ago

which alphapix do you have he 16 or the 4 are you daisy chaining the dmx boards 1 off the other


Reply
Posts: 44
Topic starter
(@theycalmegriswal)
Trusted Member
Joined: 10 years ago

I have the 16. It has 3 RS485 ports. Once I can get to the first dmx board, I will daisy chain off of it to the other one.


Reply
Posts: 1592
(@ruppro)
Noble Member
Joined: 11 years ago

IN the web page for the AplhaPix you should be able to set each of the DMX outputs, universe #, start # and # of channel (note not to overlap w/ the pixel outputs) then you configure this also in your sequencing software.


Reply
Posts: 44
Topic starter
(@theycalmegriswal)
Trusted Member
Joined: 10 years ago

That was what I thought but wasn't for sure. So I have set universe 17 , 18 for two additional dumb controllers. In xlights I then will use that universe but change the start channel until I have used all channels on the controller.

Last question,
I am planning on taking a CAT5 cable, cutting the end off, wiring the strips to positive and the solids to negative on the RS485 jack. Then run this to the input of the dumb controllers. That sound about right?

Thank you for your help.
Now comes the interesting part of sequencing.


Reply
Posts: 1592
(@ruppro)
Noble Member
Joined: 11 years ago

NO that is not right!

You will need to get the pinout for the RJ45 jack on the DMX board, most likely will be Data+, Data- and Grnd, what are the outputs on the Alphpix labeled?

RJ45 pinout looks to be

DMX+ => Orange/White
DMX- => Orange
GND => Blue

But you may want to confirm w/ HC. In looking at the Alphapix, they provide setup assistance, to what degree depends on what you purchased, but I would think that their free "Hardware Setup Assistance Only - EXCLUDES All Network / PC / Sequencing Software Setup" would provide you w/ the instructions on how to connect the DMX boards and how the cable needs to be wired. I would give their support a call.


Reply
Posts: 44
Topic starter
(@theycalmegriswal)
Trusted Member
Joined: 10 years ago

The output is RS485 and labeled + and - and ground. I purchased the setup assistance but every email I send gets kicked back, have called and left messages as well. They talk about wiring the RS485 in a video but do not show anything but states I do not need a dongle because the board is setup for this. I have watched tons of videos and can't find anything. On HC website they have a CAT5 wiring explanation that shows all solids negative and strips positive. Kinda of on my own here trying to understand how to do this.


Reply
Posts: 1592
(@ruppro)
Noble Member
Joined: 11 years ago

Doing a little more digging, I may not have the pinout completely right it may be,

DMX

DMX+ => Orange/White => Pin1
DMX- => Orange => Pin 2
GND => Brown & Brown/White Pins 7 & 8

So you could connect the Orange pair to DMX+/- and then connect the Brown pair to GND, and if that did not work you could then test w/the Blue pair.

They look to have a live chat option (at the bottom of the page) but is offline today, may want to check them during business hours tomorrow.


Reply
Posts: 44
Topic starter
(@theycalmegriswal)
Trusted Member
Joined: 10 years ago

ok thanks.

Does the way I am doing it in xlights sound about right?


Reply
Posts: 1592
(@ruppro)
Noble Member
Joined: 11 years ago
theycalmegriswal wrote:ok thanks.

Does the way I am doing it in xlights sound about right?

Yes, In Xlights, you would create your e131, IP of the Alpha, Universe # (17), # channels (30) for your 30 port controller.

note update on the pinouts, I think I have found the correct one


Reply
Page 1 / 2
Share: