Creating standalone...
 
Notifications
Clear all

Creating standalone system using FPP and ESPixelStick?

11 Posts
6 Users
0 Reactions
6,031 Views
Posts: 66
Topic starter
(@macboy)
Trusted Member
Joined: 7 years ago
[#52598]

I’m trying to set up a stand-alone system using the FPP wireless network being broadcast from the Pi and one ESPixelStick. What I cannot figure out is where to determine what IP address I need to assign to the PixelStick so it can connect to the Pi.

I’ve been digging around for an answer to this but it all keeps coming back to search results pointing to finding or setting IP addresses for the Pi itself. I thought maybe I could use DHCP on the PixelStick but that didn't seem to work so now I have one PixelStick that I think I need to reflash so I can reassign the original (show network) IP address.

(Edit - Sorry, this went into the a nutcracker thread. Please feel free to move it to the FPP thread.)


10 Replies
Braveit1
Posts: 577
(@braveit1)
Honorable Member
Joined: 19 years ago
Reply
Posts: 66
Topic starter
(@macboy)
Trusted Member
Joined: 7 years ago

Ha! That's cool. I just want to use the gear I already have on hand here since it's a one-off. Short term use project.


Reply
Posts: 66
Topic starter
(@macboy)
Trusted Member
Joined: 7 years ago

Isn't the Pi already acting as a DHCP server with the way FPP has been setup?


Reply
Posts: 1592
(@ruppro)
Noble Member
Joined: 11 years ago

1st thing you need to get is a Wrieless Access Point that is broadcasting an SSID for both the Pi and ESP to connect to so they can talk to each other, you cannot just connect 2 device together by WiFi.


Reply
Posts: 447
(@glycerine)
Honorable Member
Joined: 7 years ago
Ruppro wrote:1st thing you need to get is a Wrieless Access Point that is broadcasting an SSID for both the Pi and ESP to connect to so they can talk to each other, you cannot just connect 2 device together by WiFi.

It sounds like he's wanting to use the Pi AS the access point.


Reply
HEMISixty
Posts: 66
(@hemisixty)
Trusted Member
Joined: 6 years ago
Glycerine wrote:It sounds like he's wanting to use the Pi AS the access point.

Sounds like an "ad-hoc" connection is wanted and that would be an interesting task with a Pi and a ESPixelStick.

Edit: This is kind of dated...but, may be of some use for the Pi end, "https://raspberrypi.stackexchange.com/questions/49660/ad-hoc-setup-in-rpi-3". And, this one might help with the code for the other side, "https://how2electronics.com/esp8266-to-esp8266-communication-ad-hoc-networking/".


Reply
Posts: 1592
(@ruppro)
Noble Member
Joined: 11 years ago
Glycerine wrote:It sounds like he's wanting to use the Pi AS the access point.

It does, but I don't know if you can do that w/ the Pi running FPP.

Also the ESP can be configured to boot to AP fall back if it can't find a wireless network, but again I don't know if it will then also support the ESPixelStick firmware and be able to accept data and control lights.


Reply
Posts: 66
Topic starter
(@macboy)
Trusted Member
Joined: 7 years ago

Thanks everyone for chewing on this with me. I started another thread in the correct forum (FPP) after I successfully managed to get the Pixelstick to grab onto the Pis broadcasting wifi network. But I haven't been able to get the lights to blink - need to look into the XLights setup and esp setups.


Reply
Posts: 1387
 kev
(@kev)
Noble Member
Joined: 12 years ago

do you plan on having more than on ESPixelstick connect to the Pi? If not, why not just use a Falcon Pi cap?


Reply
Page 1 / 2
Share: