What size pole?
 
Notifications
Clear all

What size pole?

30 Posts
11 Users
0 Reactions
11 K Views
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
algerdes wrote:The movie was Wizard of Oz, the scene was when the wizard was giving out their "medals". Scarecrow did the line.

IF you want to stay with the "common standard" (half as wide as tall), 15' angled side would take around 14' 6" of pole. (7' wide base, 15' hypotenuse = 14'6" pole).

The color of the sky is .... (oops, wrong forum)

@ 4inch spacing this sounds very good 🙂


Reply
JasonPortwood
Posts: 753
(@jasonportwood)
Noble Member
Joined: 17 years ago

This calculator is great. Both for the measurements and the visualization.

http://www.altoonalights.com/mega/mega_calc.php

-
Jason


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

I use 5 sticks of 3/4 inch electrical pvc with about a foot cut off each. So a little less than 44ft round. First few years I just layer it on the ground. Then I have a 20ft flag pole.


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

Lol. I know the scarecrow was wrong about the triangle. But the point remains. Once you figure out the diameter you want the base to be, you can figure out the rest.
I tend to use the ratio of 4 or 5:1. That is, the height is 4-5 times the radius of the base.
As for pixel density, the opinions are all over the map on that. It mostly depends on whether you're treating your tree as a video display or a tree. A tree can be much less dense. If using it for video you want it to average as a square ratio. The distance between the strings at a point somewhere near the middle of the height should be equal to the spacing of the nodes along the strings.

--Jon Chuchla--

Sent from my iPhone using Tapatalk


Reply
Wolfie
Posts: 2225
Topic starter
(@wolfie)
Noble Member
Joined: 11 years ago

so it seems like ~14 is the butter zone here. Gotta git this done. I can tweak it next year. I just needed a good start point for this year.

I have a center walk and I intend to place it centered in the walk so it will have a concrete platform. I may look into drilling out the walk and sinking a well pipe or other fixture in place for next year. I am not sure I will keep this tree anyway. Its a lot shorter than I was lead to believe when I bought the lot of light parts. I was looking more at wanting a 20-25 tall tree this year. And the pixels in this are 5v which means injection every 50. If I read the forums correctly, 12v can go 100 in a chain before needing power injection. At 100px per that should get me 33' legs so I can start pushing up at the 30' tree point. I can repurpose these for something else in the display.

Do yall run guys above the apex (above strands but below topper) or below strand apex?

Also, not this year but later..I ran across a reference to a jump pole and found the monk instructions page. I will likely go to that method for next year.


Reply
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago
Skunberg wrote: ... You can find the angle "you" like best.

No better words have been spoken at this time of the year! :happycrying:


Reply
Wolfie
Posts: 2225
Topic starter
(@wolfie)
Noble Member
Joined: 11 years ago

except I am in 'gotta git it done' mode. I will make it the way I like...next year. I have ~350 days to make it better for next year.


Reply
jnealand
Posts: 956
(@jnealand)
Prominent Member
Joined: 19 years ago

Making the jump pole has been one of my better decisions. Have not had a mega tree collapse since I built mine.


Reply
Wolfie
Posts: 2225
Topic starter
(@wolfie)
Noble Member
Joined: 11 years ago

yea, it seems like a pretty good idea and is reasonable in cost. but I don't have time for the portable hole it needs for this year. So I am just going to hit home depot tomorrow for some 3/4 black iron pipe and fittings and go with an uncomplicated pole this year.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Here is a video my custom mega tree pole .


Reply
Page 2 / 3
Share: