Portable Hole in Pr...
 
Notifications
Clear all

Portable Hole in Progress

11 Posts
3 Users
0 Reactions
7,324 Views
Posts: 447
Topic starter
(@glycerine)
Honorable Member
Joined: 7 years ago
[#52895]

My portable hole form, ready for concrete. Mostly Walter Monkhouse's Portable Hole II design with a few slight modifications. I like how the Zembruskis setup their Portable Hole Lite for the eyebolts on the corners, so I used that idea. I also drilled a few "holes" in the perimeter of the form with a forstner bit, thinking that might help the concrete and form "hold" each other better, since the concrete would protrude into the wood. The nails are probably plenty, but hey, I figured it can't hurt. I also made the whole thing slightly larger, so it will be a tad heavier than the PHII.

PHForm

10 Replies
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

can you provide the link/reference for the eyebolts?
Very nice work for sure!


Reply
Posts: 447
Topic starter
(@glycerine)
Honorable Member
Joined: 7 years ago
Reply
Posts: 447
Topic starter
(@glycerine)
Honorable Member
Joined: 7 years ago

Oh, and the pdf will show this, but just to explain, the washer/bolt/nut that you see in each corner is just there to hold the pipe fittings in place until the concrete is poured. Those will be removed and, when in use, eyebolts will be inserted into those pipes and the tether system (turnbuckles) will attach to those eyebolts. (The eyebolts that are seen in my photo are to add strength to the pipes where there will be tension because of the tethering system.)


Reply
Posts: 447
Topic starter
(@glycerine)
Honorable Member
Joined: 7 years ago
MikeKrebs wrote:I am quite understanding about the eyebolts. Are you just dropping them in the pipes in the corner? Or are they screwed into something?

They just drop in.

MikeKrebs wrote:Is there a particular reason to remove the board on the bottom?

I've wondered the same thing. I thought about leaving it as long as I can get a good seal on it, since it's untreated.


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

Since this just seems to keep the concrete in, it seems to me you could lay down wax paper on a hard flat surface like a garage floor before you pour the concrete.

MikeKrebs wrote:Is there a particular reason to remove the board on the bottom?

Reply
Posts: 447
Topic starter
(@glycerine)
Honorable Member
Joined: 7 years ago

Here's my final product. The bottom isn't as smooth as I'd hoped, guess I didn't tamp it in good enough at the beginning, but the top is nice and smooth. Should I be concerned about the bottom and possibly patch it with more concrete or is this normal?

Portable Hole Top s

Portable Hole Bottom s

Reply
Posts: 486
(@uncledan)
Honorable Member
Joined: 11 years ago

The bottom of mine looked very similar. I wouldn't worry about it. After many years I'm retiring my portable hole this year. Heard of people having issues on larger trees. Weakest point is the thread on the 2" pipe that screws into the coupling. I put a 4 ft sleeve of 2-1/2" PVC in the ground 48" with about 600 pounds of concrete last weekend.


Reply
Posts: 447
Topic starter
(@glycerine)
Honorable Member
Joined: 7 years ago
uncledan wrote:The bottom of mine looked very similar. I wouldn't worry about it. After many years I'm retiring my portable hole this year. Heard of people having issues on larger trees. Weakest point is the thread on the 2" pipe that screws into the coupling. I put a 4 ft sleeve of 2-1/2" PVC in the ground 48" with about 600 pounds of concrete last weekend.

I recently saw a post where someone's pole broke at the threads while they were lifting it in place. I was thinking of maybe "sleeving" the inside with a slightly smaller pipe and some jb-weld or something like that if necessary. Not sure if it would really help. I am only starting off with a 12ft, 75x32 so I'm not too worried about it. I just won't put the pole in until the hole is in place


Reply
Posts: 486
(@uncledan)
Honorable Member
Joined: 11 years ago

My tree is 48x110 and portable worked fine with 70+mph winds for many years. I wouldn't be concerned if I was you.


Reply
Page 1 / 2
Share: