Planning on adding a smallish mega tree this year.
It is going to be a 16 x 50 x 180 degrees with 2 inch vertical spacing.
I plan on making the topper out of wood, with drilling evenling spaced holes for J hooks. Similarly, The bottom ring will have J hooks also.
50 LED's spaced 2 inch apart is a little over 8' long. Depending on the diameter of the base, the height will probably be around 7 feet. I plan to elevate the bottom ring aprox. 1 foot off the ground, and using a 23" star from Bosocoyo on top. Probably puts the top of the start 10 to 11 feet off the ground. Also, the yard where the mega tree will be placed slops a little bit down at the front, so the base will have to be designed to compensate for this.
My questions are:
1. What are good proportions for a Mega Tree. i.e. what would be a good diameter for the base?
2. What is a good diameter for the tree topper?
3. I would like to make the bottom ring out of metal conduit - was thinking about building a form to bend it. is 1/2" good enough? or should I make the bottom ring out of PVC? I would think the PVC would bend too much and not be very sturdy.
4. I have seen many different designs on hear for the base - concrete, 2x4, etc. I was thinking a 2x4 Tee and putting a couple guy-wires on the tree.
5. What is the best method to "hold up and secure" the bottom ring (I would like to have it around 1 foot off the ground)
6. I will be using bullet nodes - I see Boscoyo has 2 different types of straps, the orginal and the new heavy duty one (without wiretire holes). Any suggestion on these 2?
Ok, probably enough questions for now.
Thanks, Shawn
sroberts1519 wrote:Planning on adding a smallish mega tree this year.It is going to be a 16 x 50 x 180 degrees with 2 inch vertical spacing.
I plan on making the topper out of wood, with drilling evenling spaced holes for J hooks. Similarly, The bottom ring will have J hooks also.
50 LED's spaced 2 inch apart is a little over 8' long. Depending on the diameter of the base, the height will probably be around 7 feet. I plan to elevate the bottom ring aprox. 1 foot off the ground, and using a 23" star from Bosocoyo on top. Probably puts the top of the start 10 to 11 feet off the ground. Also, the yard where the mega tree will be placed slops a little bit down at the front, so the base will have to be designed to compensate for this.
My questions are:
1. What are good proportions for a Mega Tree. i.e. what would be a good diameter for the base?I went 1/2 the height. Mine is 20’ tall w/@10’ bottom ring. Mine is a 270 tree.
2. What is a good diameter for the tree topper?
I kept mine as small as possible. I have 32 strings. My topper is @ 12” across. I staggered my hooks with 16 on the outside ring and 16 on the inside. Space just far enough apart to put the strips in between the outer row. I didn’t want a huge top on my tree, just my preference. It’s a little bit of a pain to get the strips all hooked in but I like the finished look.
3. I would like to make the bottom ring out of metal conduit - was thinking about building a form to bend it. is 1/2" good enough? or should I make the bottom ring out of PVC? I would think the PVC would bend too much and not be very sturdy.
I wouldn’t use PVC. I don’t feel it’s strong enough. I made mine out of wood. When it needs to be replaced I will be using 1/2” metal conduit. Already have it in the garage. Just need to get to it some year.
4. I have seen many different designs on hear for the base - concrete, 2x4, etc. I was thinking a 2x4 Tee and putting a couple guy-wires on the tree.
5. What is the best method to "hold up and secure" the bottom ring (I would like to have it around 1 foot off the ground)
I use the 2x6 treated lumber X for the base w/guy wires. I made. Cable guy wires. 3 from the top and 3 from the center. Attached to screw-in anchors. Solid as a rock
The vortex 16” ones6. I will be using bullet nodes - I see Boscoyo has 2 different types of straps, the orginal and the new heavy duty one (without wiretire holes). Any suggestion on these ?
I use bullet nodes and the standard ones with the support clips. Zero issues in 5 years with them.
Ok, probably enough questions for now.
Thanks, Shawn
See answers to your questions above
Sent from my iPhone using Tapatalk
My base is an old steel plate basketball base. It has two vertical posts welded to it and my tree post slides right over the welded post. there is no strict right or wrong way to make a mega tree. It is all about what looks good to you. My 15' tree has a 6' base and 100 pixels per leg. This is what looked good to my wife and I. We did try other configurations (taller/ shorter narrower/wider) and liked this one the best.
My tree is similar to your config. I used conduit as a base and used a form to bend it and also have it off the ground:
More info on base construction in my thread: http://doityourselfchristmas.com/forums/showthread.php?42817-2016-Mega-Tree-With-Public-Remote-Control
As Martin said, there is no right or wrong way. The most important factor is that you secure it very well. Especially if it is near where people could be. The last thing you want is for it fall over, worse yet it falls over and hurts someone.
Sent from my iPhone using Tapatalk


