I did not want to hijack James interest or GB threads with this so I'm starting this thread to share my ideas and hope that others can give input and/or share their ideas as well. This is in regards to the pixel mounting strips that James just did a group buy on that a bunch of us are using to make mega trees. If the James and/or the mods want to combine the two threads (not sure if that is even possible), I'm fine with that!
I am using these strips to make a mega tree with 32 strands of the 2811 50 pixel strands at 4" spacing. The tree will have an approximate center pole ground to top plate height of 16'. I would like to keep the tree as close to 180 degrees as possible but it will probably end up being around 200-220 because of top plate space constraints. I am fine with the extra degree of the tree, more coverage on the sides is not a bad thing in my situation.
When I started thinking about how to attach these, I initially thought about the d ring method that was used for the colormotions tree and the 3/4" band strapping. With these strips being 1/2" wider than that, the d rings would need to be at least 1.25" wide, all I could find wide enough was d rings that were 1.5". I prefer a smaller diameter top plate to give the mega tree more of a natural point at the top so the wide d rings would force the diameter to be >20", I would prefer to keep it down near a diameter of 16-17". This led me to start thinking of other options.
I found the following d rings at home depot http://www.homedepot.com/p/OOK-20-lb-Steel-D-Ring-Hangers-2-Pack-50207/100058482 , they appear to be for hanging heavy picture frames, etc. The d ring on these is 3/4" and so gives me the attachment room at the top that I want. The only downfall is that the d ring is only so long and therefore can only extend over the end of the strip so far which may lead to the strips touching at the top before they "feather out". I set up a 5' piece of strip with one of these on the top and one of these on the bottom hanging from my garden trellis with a 25 lb weight hanging from it. you can see pictures below.
Positives of d ring picture hanger method
-cheap (you can get 50 of these for under $20 on amazon)
-quick/easy
-3/4" wide
Negatives of d ring picture hanger method
-only extends about 3/4" past end of strip which may not allow the strips to feather out enough and not touch on smaller diameter top plate.
-requires you to drill new holes in mounting strip for attachment
-as you can see in 2nd picture below, when I twisted the strip the d-ring shifting a good deal on the hook to allow the top of the strip to turn maybe 20 degrees to either side, not sure if this will be an issue in wind, etc.
I other idea i had was to use 3/4" wide x 1/8" thick custom cut and drilled aluminum bar stock http://www.homedepot.com/p/Everbilt-3-4-in-x-48-in-Aluminum-Flat-Bar-with-1-8-in-Thick-801917/204273967 . This allows me to make the bar stock as long as I want to extend over the end of the strip to make sure the strips have room to feather out without touching at the top. The bar stock was cut on my horizontal metal bandsaw and then I drilled two holes in the middle to line up with the mounting holes that were already there from James production. I then drilled a 3rd hold at the end of the flat bar that barely slides on to j hook. The idea was that with a tight fit between the j hook and the hole in the bar stock that the top of the strip would not be able to rotate side to side at all and would facilitate a straight row of pixels. I used #10x3/8" machine screw/nuts to attach the strip/bar stock but if i go this route I will likely use rivets for a quicker/more permanent approach. I have attached pictures of this set up in the next post
Negatives of aluminum bar stock mounting
-more work
Positives of aluminum bar stock mounting
-top of strip will not rotate side to side due to tight fit between drilled hole and j hook (picture shown on next post)
-able to extend mounting hole as far past end of strip as needed to facilitate space between strips as they feather out towards bottom
Let me know what you think and/or your ideas!
I simply left the top hole empty..and will use that to attach to my hooks at the top using a few fender washers and a 1/4" bolt
I used #10 x 1 1/2" screws and washers to fold over top. That gave me a double reinforced point to hang on hook head. At the bottom same thing and I'm using vortex 7" anchors (4 pk at lowes about $4). I'm using zip ties to tie between bottom and anchors so I can move until just right. Zip ties can hold 75 lbs so they keep it tight. Even though we just had 2" of rain in the past 2 days and my yard is a but sandy and has loose soil - they all held tight!
I used grommets from Harbor Freight. http://www.harborfreight.com/103-piece-1-2-half-inch-grommet-installation-kit-30037.html
I enlarged the last 2 holes and then folded the end so the grommet goes thru 2 holes.








