Sean:
Does each PVC tube (looks like 1" x 4" long maybe) shown on your "how to" video contain an individual controller? If so, is that where you put your pixelnet controllers? They look larger than this based on researching DLA.. Thanks!! DanJ
Ray Wu has good products but if you are not buying in large amounts the shipping costs get expensive. Try DIYLEDEXPRESS, Todd has great deals on pixels and shipping within the US is cheap.
As far as controllers, read the auschristmas manual posted, that is the best resource you will find!! There are several controllers available, all depends on what you want to do and how many pixels you want to control. I find the Sandevices products are very versatile and is my choice. Depending on the number of pixels you want to use, an E6804 is most likely your best option, E682 would be more along the lines of high density, multiple trees or displays. An E6804 is small, you can mount it in a tube, but you still need a power supply and somewhere to make your connections. The CableGuard CG1500 enclosure (DIYLEDEXPRESS carries these as well) will hold a power supply and the E6804 controller. The reason I like the Sandevice products is they have been around a while, web based setup is awesome, can support numerous types of RGB's and can run off of 5 or 12 VDC. In the E682 you can even use both 5V and 12V off of the same board, E6804 one or the other. I also use a wireless router as a bridge so all I have to do is run power to my controller and router, then connect to my home network.
I know there are alot of experts out there, but so far I have had good luck with the WS2811 5VDC RGB Strings. Strips look awesome but are very delicate, if using them you will need to protect and support them, with the strings I have had good luck with using electric fence wire for the supports, then wire tie the RGB strings to them for support. Strips are higher density but also cost 2x what the strings do. The electric fence wire is cheap, $40 for 1/4 mile of it.
As far as power injection it all depends on your set up and your connections. If you try to just twist wires together and tape them you will get poor performance with anymore than 1 string in series, no biggy, just jump the 5vdc to the input of the next string, crimp connectors are a bit better, maybe 2 or 3 strings before needing to add power again. I have a tree running now with 1200 RGB's on the tree and 50 on the star. I "soldered" extensions and connectors for every joint and I am running 6 strings without injection with no noticeable loss on 5VDC strings. Also any extensions I use on mine I always use #12AWG to minimize voltage loss. I even have a few running 50-60' away from my controller with no null pixels and no noticeable loss on the RGB's. How you make your connections is critical to how well it will perform.
DanJ wrote:Sean:
Does each PVC tube (looks like 1" x 4" long maybe) shown on your "how to" video contain an individual controller? If so, is that where you put your pixelnet controllers? They look larger than this based on researching DLA.. Thanks!! DanJ
Inside those tubes are RJ's SSC's (Smart String Controllers) They connect back to a Smart Hub or similar device and use Pixelnet.
I did a search for smart string controllers but not get a good "hit". Are those mentioned on this site anywhere??
Thanks very much.
DanJ wrote:I did a search for smart string controllers but not get a good "hit". Are those mentioned on this site anywhere??
Thanks very much.
RJ's equipment (SSC,hubs,etc) is featured in his site. His board avoids technical discussion in favor of ease of support for the equipment he designs. This site tends to go into deeper technical discussion and the Lynx (RJ's line) is not as popular here. I happened to start at this site and use mostly Renard equipment for my non-pixel lights and RJ's equipment for my Pixels.
Here's a link to the Wiki entry at his site where you can find just about anything you want about his stuff.
http://www.diylightanimation.com/wiki/index.php?title=Equipment#Smart_Strings
The SSC's baord is about 4" long and fits into 1" thinwall PVC available at Lowes. If you need exact sizes let me know and I'll measure one of mine.
