Megatree Question
 
Notifications
Clear all

Megatree Question

11 Posts
6 Users
0 Reactions
5,137 Views
Posts: 127
Topic starter
(@s196635)
Estimable Member
Joined: 14 years ago
[#24339]

I am doing a MegaTree for this year display and Have only one question, as shown in the image below the tree is red and green, I would like to know how to connect the channels? Is it 1 Controller per colour or Red Green Red Green in one controller?

Screen Shot 2013 02 02 at 6.03.38 PM

10 Replies
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

your mega tree says pixels for 2013.

you need to specify types

Controller ac > dc > or pixel ?

red and green what ?

incans or leds, pixels or dumb rgb ?


Reply
Posts: 127
Topic starter
(@s196635)
Estimable Member
Joined: 14 years ago

I have decided to go with red and green LEDs over 32 channels of Renard. I don't think i am going to start with pixels until next year.

angus40 wrote:your mega tree says pixels for 2013.

you need to specify types

Controller ac > dc > or pixel ?

red and green what ?

incans or leds, pixels or dumb rgb ?


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

If you have a controller with 32 channel capability, you could have each string of lights on its own channel.

It would be your choice as to how you want to connect them , just 1 thing to keep in mind is connecet them sequentially cw or ccw


Reply
Posts: 127
Topic starter
(@s196635)
Estimable Member
Joined: 14 years ago

Thanks! I think thats what ill do, I am using 2 SS16's for that mega tree with LEDs from HLE(2 cases of each red and green, cases of 24).

angus40 wrote:If you have a controller with 32 channel capability, you could have each string of lights on its own channel.

It would be your choice as to how you want to connect them , just 1 thing to keep in mind is connecet them sequentially cw or ccw


Reply
Posts: 1792
(@barbotte)
Noble Member
Joined: 17 years ago

what ever you decide is good but i would try to do a spiral if you could .. way better effect and you dont need as many light to make the tree look full mine is 22 ft tall 10 ft base and i only used 24 string and its full ,,, cheer


Reply
Xenia
Posts: 1358
(@xenia)
Noble Member
Joined: 15 years ago

I would run a single color on each SS16. I ran 4 SS16 on my mega tree this past Christ. One for 16 white, One for 16 multi, One for 16 red spiral, one for firestick and star. At one point I had to pull a controller due to moisture. If I had mixed the Colors I would have lost two effects. As it was I only lost white for that evening and most people did not notice.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Henri you are s19's next door neighbor lol . you could help set ip all up ! lmao 🙂


Reply
Posts: 1792
(@barbotte)
Noble Member
Joined: 17 years ago

what you could also do is 2 type of tree in 1 ..... 1 color stright and the second color go spiral ......all you have to do is install the first color straigh as you were planning then the 2 color attache on top then from the bottom go around the circle of your tree about 1 turn maybe 1.5 turn the streiigh color would act as your guide wire ... i have seen it done and it look pretty cool ... and as i said spiral you need half of the string amoung so you can used the extra channel for something else ...


Reply
yosemite
Posts: 289
(@yosemite)
Reputable Member
Joined: 17 years ago

I did a hybrid spiral last year, straight in green and spiral in multi. I did 24 channels each color on a 15ft tree 10ft diameter looks nice and full but
the spiral takes about 2 ft more wire to wrap around then the straight. I had to double up the last few ft of the straights to keep them off the ground.
Powered each color per board the load is light only one string of 100ct per channel


Reply
Page 1 / 2
Share: