I know the calculator is very good to use for planning. My question is more of a realistic question...pixel density. I will be doing a 12' tree. 180 degree, 6' diameter (based on the 50% rule, 2" spacing. This is where my density question comes into play. Is it better to have 24, 20, or 16 strings?
I would rather do this right once than do it wrong and have to redo it. If I go with 24 strings, I am looking at ~3,600 pixels (that will give me an emergency string if once goes out). I am not sure with that would be too dense or if it is better to go with 20 or 16 strings.
Depends on the distance for viewing. The closer the distance the more density. I have a 20’ 32 100 pixel strings on a 270 degree tree. But I have a fairly close viewing area.
Sent from my iPhone using Tapatalk
TSL wrote:Depends on the distance for viewing. The closer the distance the more density. I have a 20’ 32 100 pixel strings on a 270 degree tree. But I have a fairly close viewing area.
Viewing distance is the key here. I would post what your viewing distance will be and you will probably get feed back on what others have done with their Mega tree setups. My Mega Tree is 180 degrees, 30' tall, 32 strings, and sits 175' back from the road. I'm happy with my pixel density at the distance. But if the tree was closer, I would be adding more strings based on the viewing distance.
I am in planning stages only so far. That means there is a lot that can change or be updated before I even make a first purchase. My street has 2 sidewalks: my side 12-18 feet and unrealistic) and the other side of the street (~40 feet and much better for viewing the house). I am trying to get a few initial things answered or at least to do more research.
Height Questions: Did anyone go with 10' and be upset for not going 12'? Going 12' and wished they had gone 15'?
String density: Assuming primary viewing will be on the other side of the street (~40 feet) on a 180 tree, number of strands and spacing is my big question. This is where 75% of the cost is going to come in.
bigrednole wrote:I am in planning stages only so far. That means there is a lot that can change or be updated before I even make a first purchase. My street has 2 sidewalks: my side 12-18 feet and unrealistic) and the other side of the street (~40 feet and much better for viewing the house). I am trying to get a few initial things answered or at least to do more research.Height Questions: Did anyone go with 10' and be upset for not going 12'? Going 12' and wished they had gone 15'?
String density: Assuming primary viewing will be on the other side of the street (~40 feet) on a 180 tree, number of strands and spacing is my big question. This is where 75% of the cost is going to come in.
Our tree is somewhere around 17-18 feet. ASAP pole is up to around 16 and there's a 2 ft star on top of that. We are doing a 180 degree tree with 16 strands of 100 pixels at 1.5" spacing. Our diameter is 8 feet across at the base, and it's about 40 feet off the street. This was our first year doing anything, and if I had to do it again I would probably do the same specs, but with 24 strands just because the view coming up the street from one side kind of needs the extra strips. In front of the house or coming from the opposite direction down the street is fine.
Given the distance on your side of the street to your proposed location, I would go for more density. At 1.5" spacing ours is just about right, but I'd love 1" spacing between pixels. I would definitely do 24 strands in your situation, but I would also do smaller spacing than 2" between pixels if it were me at that distance. I'm not sure where your numbers are coming from, though, as 2" spacing on a 12 foot tree would only need around 100 pixels per strand, if that, and you're saying 3600 for a 24 strand tree. You said 6 foot diameter, but did you actually mean radius?
