ThinkAgainAgain wrote:... running my data cables every 400 pixels (per universe) I know it's short of the 510 per, but it's clean and easy running at the base of the tree (I think).
Just to clarify since it won't affect your setup, just your configuration in your controller and possibly sequencing software (depending on what you're planning to use), 400 WS2811 Pixels is actually 1200 Channels, which is a little over 2.35 Universes. Remember that each pixel has a Red, Blue and Green channel.
Not a huge deal since you can run more than one universe off each E682 output, but something to keep in mind when you are configuring the E682.
AuburnLights wrote:Just to clarify since it won't affect your setup, just your configuration in your controller and possibly sequencing software (depending on what you're planning to use), 400 WS2811 Pixels is actually 1200 Channels, which is a little over 2.35 Universes. Remember that each pixel has a Red, Blue and Green channel.Not a huge deal since you can run more than one universe off each E682 output, but something to keep in mind when you are configuring the E682.
Thank you - I just looked it up and it appears as tho I just squeeze in - under the 6120 max channels... My tree will have 2,000 pixels or 6,000 channels.
ThinkAgainAgain wrote:Thank you - I just looked it up and it appears as tho I just squeeze in - under the 6120 max channels... My tree will have 2,000 pixels or 6,000 channels.
You're correct, but keep in mind that 12 universes (6,120 Channels) is only available on E1.31 using unicast. The limit for multcast is 7 Universes (3,570 Channels). Again, you just have to make sure and configure your controller correctly is all, the default is multicast E1.31.
Also, you're probably going to want to use all channels in order, so your configuration would be something like this (depending on how you hook things up, but the Universe numbers and channels I believe will be correct, but it's late:)):
| Start | Address | End | Address | |||
| Outputs | Outputs in Use | Length Pixels | Universe | Channel | Universe | Channel |
| 1-1 to 1-4 | 2 | 400 | 1 | 1 | 5 | 360 |
| 2-1 to 2-4 | 1 | 400 | 5 | 361 | 7 | 30 |
| 3-1 to 3-4 | 1 | 400 | 7 | 31 | 9 | 210 |
| 4-1 to 4-4 | 1 | 400 | 9 | 211 | 11 | 390 |
You may also want to consider setting "Zigzag Every" to 80 Pixels, it may make your sequencing easier. This is personal preference though, not required.
MikeKrebs wrote:...Btw, you might want to look at the group buy on falcon Christmas for power distribution board. Might help you out along the way. I think time is short on getting in but it is still open.
Funny you mention this, I ordered some yesterday. The Co-op is open until 2/21/16. I agree, these are pretty slick for Power injection on a Mega Tree or other pixel dense props.
Here's the Link
my understanding is that you can only have 170 pixels per universe. which would be 510 channels. 170 x 3 (3 for RGB) in your picture you have 400 pixels or 1200 channels for the one universe. i dont think it will work. someone correct me if im wrong.
AdamZ wrote:my understanding is that you can only have 170 pixels per universe. which would be 510 channels. 170 x 3 (3 for RGB) in your picture you have 400 pixels or 1200 channels for the one universe. i dont think it will work. someone correct me if im wrong.
You're correct that there are only 170 Pixels in a Universe (510 Channels), but you can't equate one connection to the E682 to a single universe. A single output from an E682 can have multiple universes of Pixels (or channels, 3 per Pixel), the only limitation (other than power draw) is that you can only have 7 universes on the entire E682 for Multicast or 12 universes on the entire E682 for Unicast. I am sure there is a logical limit to the number of pixels on a single output, but I have not read what that is exactly. I know that you can have 4 universes of Pixels on a simple ESPixelStick (680 Pixels) using Unicast so I would think that the E682 would be able to do at least that much. The only caveat to this is GECEs, which are limited to 63 Pixels per output (on either the E682 or ESPixelStick) due to their lack of addressing space. It's not an issue with the controllers, but instead how GE defined the protocol for the GECEs.
You can certainly connect 170 Pixels to each output of the E682 to make it easier to configure, but this is not a requirement. Also, keep in mind that in that configuration you could only use 7 connections in Multicast or 12 connections in Unicast.
In the scenario that the OP is asking about, he will only be using 5 connections on the E682. Each with 400 Pixels and that equates to just under 12 Universes on the entire E682.
AdamZ wrote:my understanding is that you can only have 170 pixels per universe. which would be 510 channels. 170 x 3 (3 for RGB) in your picture you have 400 pixels or 1200 channels for the one universe. i dont think it will work. someone correct me if im wrong.
Yes, I didn't draw in the data cables correctly. The data cables would be every two stands or 160 pixels.
I plan on running 12 universes on unicast.
Sent from my SAMSUNG-SM-G890A using Tapatalk
ThinkAgainAgain wrote:Yes, I didn't draw in the data cables correctly. The data cables would be every two stands or 160 pixels.I plan on running 12 universes on unicast.
Oh, okay, then disregard my example configuration. That was assuming that you were doing 400 Pixels per output.
AuburnLights wrote:You're correct that there are only 170 Pixels in a Universe (510 Channels), but you can't equate one connection to the E682 to a single universe. A single output from an E682 can have multiple universes of Pixels (or channels, 3 per Pixel), the only limitation (other than power draw) is that you can only have 7 universes on the entire E682 for Multicast or 12 universes on the entire E682 for Unicast. I am sure there is a logical limit to the number of pixels on a single output, but I have not read what that is exactly. I know that you can have 4 universes of Pixels on a simple ESPixelStick (680 Pixels) using Unicast so I would think that the E682 would be able to do at least that much. The only caveat to this is GECEs, which are limited to 63 Pixels per output (on either the E682 or ESPixelStick) due to their lack of addressing space. It's not an issue with the controllers, but instead how GE defined the protocol for the GECEs.You can certainly connect 170 Pixels to each output of the E682 to make it easier to configure, but this is not a requirement. Also, keep in mind that in that configuration you could only use 7 connections in Multicast or 12 connections in Unicast.
In the scenario that the OP is asking about, he will only be using 5 connections on the E682. Each with 400 Pixels and that equates to just under 12 Universes on the entire E682.
Hmmmm,... I can run 400 pixels from one output?
That would be easier for sure... Thanks, I was thinking I had drawn the cables wrong.
Sent from my SAMSUNG-SM-G890A using Tapatalk
ThinkAgainAgain wrote:Hmmmm,... I can run 400 pixels from one output?That would be easier for sure... Thanks, I was thinking I had drawn the cables wrong.
Sent from my SAMSUNG-SM-G890A using Tapatalk
I don't have an experience with that many off of an E682, but I do with an ESPixelStick (I use these for my Arches, 2-240 Pixel arches per ESPixelStick). I haven't read anything to the contrary regarding the E682 (I do have some, but I don't have that many pixels per output. Keep in mind that you won't be able to to power the entire string through the E682 as you'll exceed the current draw per output, but looking at your drawing, you're going to provide power and injection outside of the E682 anyway. The only thing you'll need to make sure (as others have already pointed out) is that all of the Power Supplies and the E682 have the same Ground reference.
