I've also been using the upper chain link fence post - once thing thats nice about that is 1" EMT condiut also fits nicely inside of it! of course it takes a lot of pipe to get to 50'
I'm using a live tulip tree for the center support. My wife stoped me with the chain saw when I mentioned a star at the top would look nice. 😀
Guy Wires
Like Elmo2resc and others suggested, I purchased a 10' upper chain link fence post to serve as my center pole. The pole is 1 and 3/8". I purchased a piece of 1.5" pvc pipe to drive into the ground and will slide the metal pole inside. I don't think that will be very sturdy by itself so I need to put up some guy wires. Can folks make suggestions?
1) What is the best material for the wire? I was thinking of 3/18" steel wire they sell at Home Depot in the cut it yourself roles.
2) What is the best way to attach wire to the top of the pole?
3) What's the best way to stake it into the ground? Tent stakes, rebar, etc?
4) What's the best way to attach the wire to the stakes?
When I say 'best' I kinda mean 'cheapest' but also realize it might be worth to spend a few extra dollars to do something correctly.
If folks have pictures, that would really help. Thanks for your help.
I am using 2 peices of 3" sch 40 pvc. Pipe to slip fittings in the middle. 1 - 10 foot piece and then one 7 foot piece. Three guy wires from top to the ground with lightwieght 2 foot augers like you would use for your kids playgym. No issues and have had no issues despite my best efforts to knock it down. 😕 All painted black with hooks screwed into the base 3 by 3 wide high to hang my SSR boxes from.
Re: Guy Wires
After I posted, I found this website. Really helpful
http://www.nevadachristmas.com/Megatree.htm
I also found this as a possible stake solution
http://www.homedepot.com/webapp/wcs/stores/servlet/ProductDisplay?jspStoreDir=hdus&catalogId=10053&marketID=401&productId=100054756&onlineStore=true&locStoreNum=8125&keyword=ground+anchor+kit&langId=-1&searchRedirect=ground+anchor+kit&storeId=10051&endecaDataBean=com.homedepot.sa.el.wc.catalog.beans.EndecaDataBean%40277011d8&ddkey=Search
but if you have better, cheaper suggestions, I would appreciate it.
If you are only going to have a 10-15 ft Mega tree you could do as i did. Goto your local garden center and purchase a steel fence post the type used for livestock that you just hammer into the ground. a piece of 3/4 thick wall like rigid conduct, not thin wall EMT conduct,inch pipe 10-15 foot tall and 2-4- 1 1/2 to 2 inchhose clamps large enough round to go around both the pipe and fence post. hammer the post into the ground. open up the clamps and slide them over the fence post. Then stand your pipe up all slide the post, there is usually some kind of indent you can stand it in. then tighten the post clamps spacing them evenly up the length of the fence post. this design should hold up a mega tree with 16 to 24 strings of lights without guide wires.
Good luck
Pete
I just used an Amateur beam center pole that I had in the backyard from my ham radio days. I knew it would come in handy one day 🙂
its 10' and did the job nicely. I Used 4 200 LED strings and split out the strands to make 16 branches (5 spare sets) of 40 LED's each (10 x 4 Colours)
I used Building Wire to attach the light strings to and
I ran the wires to the top of the pole and then down the pole to where the controller will sit.
The Pole and lights will go to a 64 output olsen 595 board that I have done on Vero and then back to the computer.
ill post some video once Im finished
My dad knocked out two 15-18 foot mega trees in about a half hour this year, we hung 12 strings of lights from each and those lights served as the guy wires.
Construction:
lower 8': Metal 1/2" electrical conduit (I think it's that size... it's standard whatever it is)
upper 10': 2X2 piece of pine
He drilled a hole into the pine that the conduit could be pounded into probably 8-10" deep.
then we took the pole and shoved it into the ground outside untill it held itself up. (maybe a foot into the ground)
finally we strung lights around the tree keeping it balanced by other strings until all 12 were up (each string went from the bottom to the top back to the bottom and had a few feet left over)
hope that helps! if anyone wants pictures I'll try to get some.
Yard swing ground screws is a good bet for the stakes. I would not use wire for guy lines just because wire is a pain in the neck to adjust. Rather a rope that does not stretch when wet (clothes line cord should do for a 10' tree). Attaching to the stake is easy by way of a "dog bone". A dog bone makes tightning and adjusting super easy. To make a dog bone just cut a dowel to about 5 - 6 inches and drill holes in the ends the same diameter as the rope. Pass the guy line through one hole of the bone then through the stake eye then through the other hole in the bone and tie a knot in the rope so it cant slip out thru the hole. To adjust just grab the bone and push it up while pulling the guy rope down. When tight the bone will bind the rope.
"trucker's hitch" works well too
