Help Planning for C...
 
Notifications
Clear all

Help Planning for Creating a Mega Tree

17 Posts
9 Users
0 Reactions
18.6 K Views
Posts: 110
Topic starter
(@corydorning)
Estimable Member
Joined: 13 years ago
[#49165]

Okay...so i'm attempting to do my first mega tree this year and I've read a lot here, but all sorts of numbers are being throw around so I'm trying to hone in on what i need. Here's what i have so far:

- I'd like my tree to be 12' to 15' tall
- Based on reading it seems like 2" spacing at the bottom seems like a good starting point
- 180* since it is set back from the street
- Using ws2811 pixels

What I don't know is:
- How many light strings do I need?
- How many pixels per strand?
- What spacing should i have between the pixels? (Was thinking 2")
- What should the radius of the bottom of the tree be?

Any help is greatly appreciated.


16 Replies
aknflyer
Posts: 371
(@aknflyer)
Reputable Member
Joined: 10 years ago

Ran the #'s:
6' dia base 12' high= 148" rounding down to the nearest inch. 2" spacing= 74 pixels
8' dia base 12' high= 151" roudning down to the nearest inch. 2" spacing = 75.5 pixels

6' dia base 15' high= 183" rounding down to the nearest inch. 2" spacing = 91.5 pixels
8' dia base 15' high= 186" rounding down to the nearest inch. 2" spacing - 93 pixels

If you meant 2" spacing between the strings at the bottom, that would be too close. On my 50 pixel tree with a 6' base I spaced 5" apart at the ring. You will need to decide on the # of strings and come up with a # for the spacing on the ring.
Mine was 24 each 100" strings spaced 2" for a total length of 8' 4". But the ring was suspended above the ground about 18" and I used bungie cords to pull the ring down to anchors in the ground. Kinda used the strings as built in guy wires. I added 2 empty strings at the back to make the ring level.
I used half of a square tube cable reel that telecom uses for cable or duct.
It worked very well for me.
Stallionet has a very good thread on this site on how he did it. I just modified a few things. Its all about how you want to go.
Hope this helps.

Tree Pic

Reply
Posts: 110
Topic starter
(@corydorning)
Estimable Member
Joined: 13 years ago

How would i go about coming up with the number of strings? any guidelines on that? also, as far as building everything out for the megatree, does anyone have bulletproof advice on what to use to make things as easy as possible for setup, teardown and storage?


Reply
kwoodard
Posts: 281
(@kwoodard)
Reputable Member
Joined: 13 years ago

Play around with the calculator/visualizer at https://www.lightshowhub.com/tools/mega-tree-calculator and see what looks good to you. For reference, I'm doing a ~18' tree this year with 2" spacing. I'm using a 10' trampoline frame as my base. I'm doing 100 pixels/strand and a total of 30 strands (3000 pixels total). There are a lot of variables that you can adjust depending upon what you are looking to do.

For ease of setup/tear down (as well as ease of building), I made my strings exactly 100 pixels and each strand has pigtails on both ends. I run 200 pixels per output of my controller (100 up and 100 down). Each strand can be individual put up or replaced if something fails during the show. Hopefully will also allow for easy storage in the off season.


Reply
Posts: 110
Topic starter
(@corydorning)
Estimable Member
Joined: 13 years ago

i see a lot of people using the trampoline base...any further info on that?


Reply
Page 1 / 4
Share: