So i am planning to add a pixel tree for this year however looking through the forum on Mega Trees not seeing anything similar to what i am planning and wanted to get opinions on sizing. The part i do know, I already have 16 strings of 25 CT GECE's to use, and i'll be using either the e680 or e682 i have as well.
My front yard it pretty small and my options of where to put my tree pretty much limits me to one spot. Due to this I don't want to block the rest of the house/display with a 12-15ft plus tree. I am thinking of a full tree with the 16 strings, and having the lit portion to about 8 ft. with the base hoop about 4.75 to 5 ft in diameter and the top of the tree at about 6.5 to 7 in in diameter. With the planned 8ft height of the lit portion, the spacing on the pixels would be just over 3 inches.
The main things i am looking for opinions on is should i go with a full tree or a half tree? I don't really plan on doing any text scrolling, and with the vertical spacing being fairly tight on the pixels the horizontal spacing i came up with would be similar to a taller tree with more strings so not sure "fullness" would be an issue. Also is the pixel spacing too tight? Should i bump up the either a foot or two to make the pixel spacing closer to the more typical 4 in (100mm)?
I am open to any other suggestions as well.
Well... I'm making a 10' pixel tree with 8 (or maybe 10) strings as a 180 degree tree. 10' because that's the size of electrical conduit and I don't feel like cutting it 🙂
I've read quite a few places that a pixel tree looks great as a 1/2 tree.
Of course you need to do what "you" want, and it sounds like you've put some thought into it. With that being said, I always like fuller tree's.
But after seeing lots of pixel trees now, I think the ones that look the best have a large area in the center that have equal spacing up and down. So the best looking pixel trees while lit, look bad in the daylight. They have large tops and small bottoms to maximize the area of equal spacing. I don't think people planed it this way but that's what I've come to believe so far.
Brian
With 16 strings, IMHO, go with a 180 degree tree. The 3" spacing is not too tight. I used CCPs last year at 3" spacing and it turned out quite nice.
Check out the 2 vids from 2012 on my site (in signature) and it will give you an idea of what it will look like with 3" spacing.
Good Luck,
Ron
dariansdad wrote:With 16 strings, IMHO, go with a 180 degree tree. The 3" spacing is not too tight. I used CCPs last year at 3" spacing and it turned out quite nice.Check out the 2 vids from 2012 on my site (in signature) and it will give you an idea of what it will look like with 3" spacing.
Good Luck,
Ron
Thanks, Watched the videos. You tree looks a little taller than what i am shooting for (guessing about 10-11 ft? on yours), but the pixel spacing looks good. Whats the horizontal spacing between your strings on the bottom?
10" at the bottom. The tree was 12.5' from first pixel to pixel 50.
Sent from my SAMSUNG-Galaxy-SII Skyrocket using Tapatalk 2
Excellent, thanks for your specs. That's pretty close to the spacing I was going to have.
I got to thinking about what you're using. 3" spacing for 25 GECEs will just be a little over 7' tall. If you want it 8', youll need another 1/8" or1/4". It will be quite bright I think. The picture on my web site was taken with everything at 50% intensity. The pixtree was RGB, RGB, etc all the way down.
Sent from my SAMSUNG-Galaxy-SII Skyrocket using Tapatalk 2
Yeah I think I came up with 3 1/8 in for an even 8 ft.
I was wondering about the brightness too I will probably have to knock it down from full as well.
I made a small tree, and I loved it. It wasn't enough for text and pictures, but I still stayed with the 360 degree, 16x25. Check it out, some videos towards the end and specs in the first post.
The-not-so-Mega-Tree

