I finally got the go ahead from the wife to check into a matrix I'am thinking of building using 49 P10 Panels.
I have only found bits and pieces of info doing a search, so I have some other questions I need answered.
I was thinking of a 7 panel x 7 panel matrix to fit our front window, here are my questions.
1- how many 30amp power supplies would I need.
2- where would I inject power ( how many P10 panels )
3-Any info on building a weather proof box for it would be great.
4- I now have about 10k channels so this would bring me around 85k channels if I understand it correctly.I have been using Vixen3 for sequencing. Can I continue using it or will I need to learn xlights.
I think that is all for now, I just want to make sure I have all the info before I make the jump.
Thanks in advance for any help.
I'll put some hardware answers below.
Traneman wrote:I finally got the go ahead from the wife to check into a matrix I'am thinking of building using 49 P10 Panels.I have only found bits and pieces of info doing a search, so I have some other questions I need answered.
I was thinking of a 7 panel x 7 panel matrix to fit our front window, here are my questions.
1- how many 30amp power supplies would I need.
I've measured panels at just under 2a per panel. The panels run on 5v power supplies. For 49 panels you'd need to be able to supply at a minimum 98a of current. The large 5v power supplies can supply up to 60a of current. You'd be fine with two power supplies.2- where would I inject power ( how many P10 panels )
The 320 X 160 panels have two power inputs on each panel. Each power cable that is typically supplied with the panels is in a "Y" configuration so each power cable powers one panel. This Y power cable connects directly to the power supply.2a - Don't forget about data cables. You will need data cables to connect the panels to the BBB/Scroller cape. The panels typically come with ~5" ribbon cables for connecting the panels to each other.
3-Any info on building a weather proof box for it would be great.
4- I now have about 10k channels so this would bring me around 85k channels if I understand it correctly.I have been using Vixen3 for sequencing. Can I continue using it or will I need to learn xlights.
I think that is all for now, I just want to make sure I have all the info before I make the jump.
Thanks in advance for any help.
Building the weatherproof case could be challenging for you since you're in a part of the country that has some freezing temperatures. This results in condensation. I'd assume you'd probably put plexiglas in front of the panels and condensation on cold plexiglass or even single pane glass will cause problems.
My Santa's workshop display has a couple large windows and in 2014, they frosted-over enough so that you couldn't really see into the inside of the workshop to watch the animatronics. Last year I added a heated defroster with two fans to help the windows clear. It was about 70% successful.
With a 7x7 panel display, you're looking at a window that's 7 feet wide and 3-1/2 feet tall if you're planning to use the 32x16 P-10 panels. If you plan to mount it outdoors, you'll want to provide for plenty of air movement inside to help keep moisture off the window and perhaps even the panels and electronics itself.
To give you a scope of the windows that frosted over, here's a photo of Santa's workshop after assembling it in the garage and before putting it outside last season...
I used terminal blocks for the power. One on the left for all the red wires to go to then power supply to it with jumpers from block to block. One in middle for ground and one on right side for power 

Sent from my iPhone using Tapatalk
Traneman wrote:I finally got the go ahead from the wife to check into a matrix I'am thinking of building using 49 P10 Panels.I have only found bits and pieces of info doing a search, so I have some other questions I need answered.
I was thinking of a 7 panel x 7 panel matrix to fit our front window, here are my questions.
1- how many 30amp power supplies would I need.
2- where would I inject power ( how many P10 panels )
3-Any info on building a weather proof box for it would be great.
4- I now have about 10k channels so this would bring me around 85k channels if I understand it correctly.I have been using Vixen3 for sequencing. Can I continue using it or will I need to learn xlights.
I think that is all for now, I just want to make sure I have all the info before I make the jump.
Thanks in advance for any help.
I will be closing out my March Pre-Sale at Midnight Thursday! Panels are going for $10.50 if you need anything let me know!
Thanks,
Darrell Pellegrin
Crockett Fantasy of Lights, LLC
www.crockettfantasyoflights.com
Here is my .02cents worth on the Enclosure....
My matrix is very small in comparison to yours (only 3X2), but to alleviate any condensation issues this is what I did:
-Created a box using plywood and plexiglass for the front, routed to fit into the plywood.
-fit the P10 panels on a melamine backer and affixed to sides of plywood by adding furring strips to each side and then placing completed panel inside enclosure.
-the completed panel then sat flush with the plexiglass I slid in (no space, snug fit).
-the power supply I used sat outside (rain proof model)and mounted at rear of enclosure. There was a terminal block and fusing for each panel mounted inside enclosure as well as Ron's 16 universe controller.
This kept things separate and I had no issues with condensation or moisture. It sat outside for 5 weeks with lost of rain, snow, ice. Had to scrape the plexiglass several times after heavy snow or storm but other than that it held up well.
I,like many others are waiting to see what james comes up with on an enclosure for the P10 panels. I was pondering about making my own,but decided against it. I'm sure it takes time to come up with something that will cater to different variations of P10 matrix builds.
Kev7274 wrote:I,like many others are waiting to see what james comes up with on an enclosure for the P10 panels. I was pondering about making my own,but decided against it. I'm sure it takes time to come up with something that will cater to different variations of P10 matrix builds.
I'm working on it! Had a few changes happen over here and it messed up my timeline. Patience my young grasshopper! It is real close.
James
james70818 wrote:I'm working on it! Had a few changes happen over here and it messed up my timeline. Patience my young grasshopper! It is real close.James
Good I've been worrying what I'm gonna do to enclosure my panel tv screen lol
I'm working on a prototype enclosure for a two sided tune to sign. 4 panels each side. Made from .03 galvasteel and black powder coat. Hope too have photos in about a week along with pricing.
Sent from my SM-G920V using Tapatalk

