LOR Controller Issu...
 
Notifications
Clear all

LOR Controller Issue/Software Related

9 Posts
4 Users
0 Reactions
10.7 K Views
Posts: 230
(@oldandslow)
Reputable Member
Joined: 16 years ago

For what it's worth, I have 3 channels come on at the same time on three different boxes running in DMX. I did as Plasma said did 1 box at a time and switched cat 5 cable. When I run the same sequence in LOR with the USB dongle all twelve boxes run fine. DMX has not been kind to me. I even put a blank cat 5 in the last box incase of bounce back as another member suggested.
The only thing I didn't try was John Storms idea of putting a 2 watt resistor on a old cat 5 cable. He has a video on how to do this.
I'm running my show and it's consistent on the off channels and I had the help of a expert with no luck.
John


Reply
Posts: 2229
(@plasmadrive)
Famed Member
Joined: 15 years ago
Protege94 wrote:I swapped out all the cat 5 cables, that didnt work. Then I did a board reset on controller 01 by jumping the pins and that corrected that specific issue. I have no idea why a CTB 16 channel AC controller would throw input values when the controller is completely output based. (There was no input board installed)

Then the next night the boxes took on a mind of their own and I had to retrace my steps. About half way through I started getting a GFCI trip. The trip was due to a bad line of c7 bulbs shorting out. I found that if I had my input pup daisy chained into my four CT controllers then I would get crazy network errors and activity. If I plugged the input pup directly to my USB adapter (has 2 cat5 outlets) then everything worked correctly.

So far no other issues have come up, other than the blizzard we had yesterday which caused my driveway arches to sag a LOT.

So if I read this correctly, everything is working ok now if you plug the Input Pup into the USB adapter, is that right? If it is, perhaps your Input Pup has something to do with the inputs showing up on the controller.. ???? maybe???? BTW, I believe the CTB16PC controllers have input pins you can use without any input board.


Reply
Posts: 2229
(@plasmadrive)
Famed Member
Joined: 15 years ago
oldandslow wrote:For what it's worth, I have 3 channels come on at the same time on three different boxes running in DMX. I did as Plasma said did 1 box at a time and switched cat 5 cable. When I run the same sequence in LOR with the USB dongle all twelve boxes run fine. DMX has not been kind to me. I even put a blank cat 5 in the last box incase of bounce back as another member suggested.
The only thing I didn't try was John Storms idea of putting a 2 watt resistor on a old cat 5 cable. He has a video on how to do this.
I'm running my show and it's consistent on the off channels and I had the help of a expert with no luck.
John

Are you aware that the wiring to the controller is different for LOR protocol and DMX512 protocol? You need a crossover cable for the first one in the daisy chain if you are running DMX. You don't need that crossover cable if you are running LOR protocol.


Reply
Protege94
Posts: 556
Topic starter
(@protege94)
Honorable Member
Joined: 10 years ago
plasmadrive wrote:So if I read this correctly, everything is working ok now if you plug the Input Pup into the USB adapter, is that right? If it is, perhaps your Input Pup has something to do with the inputs showing up on the controller.. ???? maybe???? BTW, I believe the CTB16PC controllers have input pins you can use without any input board.

Yes if I have the input pup directly connected to the adapter it works perfectly fine, but if I put it into the daisy chain it throws everything off. I so know the CTB16PC has input pins and I actually have the board for that, but none of my controllers are close enough to use that so I went with the input pup instead.


Reply
Page 2 / 2
Share: