Extra Parallel port
 
Notifications
Clear all

Extra Parallel port

20 Posts
9 Users
0 Reactions
12 K Views
A Marchini
Posts: 426
(@a-marchini)
Reputable Member
Joined: 19 years ago
cobraman44 wrote:If you use a desktop make sure you have an ISA slot. The PCI LPT ports do not work. I tried 3 different chip sets and none work with XP. I read several articles of people having the same issue with parallel port zip drives.

I was curious if you tried a card like this?
http://www.kanda.com/index.php3?bc=direct&bw=%2Fproducts%2FMisc%2FPCI-LPT.html

A lot of cards I see use the ITE chip and it only is one mode only. Something makes me think they may have screwed something else up along the way (however, now I am thinking the thing they screwed up may be voltage, PCI slots these days are 3V, perhaps the cards have insufficient drive voltage).
Anyways, the cards based on the NM9835 may be more configurable an likely to function as required.

Tony M.


Reply
cobraman44
Posts: 258
Topic starter
(@cobraman44)
Reputable Member
Joined: 19 years ago

That board is based on the NetMos chip. I tried one of those as well. All the boards I tried had the hardware capabilities. It was the drivers that was the issue. The drivers for NT and Dos would allow you to make the proper selections. Drivers for XP, 2000, 2003 would not not. What I have read is that it is the way the driver has to interact with the OS.


Reply
jstlucas
Posts: 96
(@jstlucas)
Estimable Member
Joined: 19 years ago
cobraman44 wrote:That board is based on the NetMos chip. I tried one of those as well. All the boards I tried had the hardware capabilities. It was the drivers that was the issue. The drivers for NT and Dos would allow you to make the proper selections. Drivers for XP, 2000, 2003 would not not. What I have read is that it is the way the driver has to interact with the OS.

Anyone ever have any luck, then, with adding another parallel port pci card? I ordered one, installed it, and then found it worked, kindof, THEN read about all the problems w. getting it to work. Yeah, mine has the netmos 9835 chip also.


Reply
Posts: 577
(@photovor)
Honorable Member
Joined: 19 years ago

Vixen accesses the parallel port via the inpout32.dll. It's this which is the problem. Inpout32.dll can only deal with 16-bit I/O addresses, which means 0x0000 through 0xFFFF. Your PCI add-in cards use a 32-bit address space. ONLY if you can get these cards to use an address in the range above, will they work.

If you had an ISA LPT add-in card, you'd have no problem. I had a PC once that I had the motherboard LPT port, and 2 ISA add-in cards, and it was very easy to program it for the ports, because they all were in the correct address range.

As for USB to printer port converters, forget that as well.

Time to pull those old PCs out of the closet.


Reply
A Marchini
Posts: 426
(@a-marchini)
Reputable Member
Joined: 19 years ago
jstlucas wrote:Anyone ever have any luck, then, with adding another parallel port pci card? I ordered one, installed it, and then found it worked, kindof, THEN read about all the problems w. getting it to work. Yeah, mine has the netmos 9835 chip also.

If the board supports I/O cycles then it can be accessed in the 16 bit I/O space. It may work if the I/O driver is executed without the PCI card driver installed. Of course... the tough part there is getting windows to tell you where the card is.
Windows may block I/O access to it even with the I/O driver in the parallel port plugin.

One thing to look at in the driver (unfortunately I don't have a card to check this) is to look in the driver tab, see if there is some kind of "legacy" check mark that may bring this card into the standard LPT card areas like 378,3BC,278.

I should just buy a card and try it. It seems the inpout32.dll appears to be able to take 16 bit i/O addresses without a problem.

Tony M.

P.S. What does "worked , kind of" mean??


Reply
jstlucas
Posts: 96
(@jstlucas)
Estimable Member
Joined: 19 years ago
A Marchini wrote:P.S. What does "worked , kind of" mean??

"worked, kind of" means that if I used Vixen 1.1, simple 595 plug-in instead of the olsen 595 plugin, and set the "number of clock cycles to hold high" to 2 (instead of 1), it ran the 595 perfectly with the pci parallel port card. However, Vixen 2 doesn't have this option to output multiple clock cycle highs like 1.1 did and I'd prefer to program in vixen 2 for Christmas 2009. (Hey, put that clock cycle option BACK IN!!!). Besides, the simple-595 only runs one parallel port, the olsen 595 will run multiple parallels.

Now, I'm also sending channels 129 through 192 out through a quad differential line driver at the output of my 2nd 595 board through a few hundred ft of cable to a receiver circuit to drive my neighbor's house, and the extra clock cycles just mess up that display horribly, can't get consistent results at all.

So, maybe having the olsen 595 plugin have the capability for the different ports to hold multiple clock cycles high might fix the problem, one 595 through LPT1 could have a single clock cycle high, the pci parallel port card version LPT2 could have 2 high clock cycles.


Reply
A Marchini
Posts: 426
(@a-marchini)
Reputable Member
Joined: 19 years ago
jstlucas wrote:"worked, kind of" means that if I used Vixen 1.1, simple 595 plug-in instead of the olsen 595 plugin, and set the "number of clock cycles to hold high" to 2 (instead of 1), it ran the 595 perfectly with the pci parallel port card. However, Vixen 2 doesn't have this option to output multiple clock cycle highs like 1.1 did and I'd prefer to program in vixen 2 for Christmas 2009. (Hey, put that clock cycle option BACK IN!!!). Besides, the simple-595 only runs one parallel port, the olsen 595 will run multiple parallels.

Now, I'm also sending channels 129 through 192 out through a quad differential line driver at the output of my 2nd 595 board through a few hundred ft of cable to a receiver circuit to drive my neighbor's house, and the extra clock cycles just mess up that display horribly, can't get consistent results at all.

So, maybe having the olsen 595 plugin have the capability for the different ports to hold multiple clock cycles high might fix the problem, one 595 through LPT1 could have a single clock cycle high, the pci parallel port card version LPT2 could have 2 high clock cycles.

OK cool. So it did work, you just need to slow the cycles down, that is understandable. I will have to check the PCI spec but perhaps I/O cycles on the PCI bus are slightly faster than the LPC bus.

Anyways, I don't think it is any major deal to get the option back in the driver. I will try to look at it tonight and post. The 595 driver is relatively easy.

Tony M.


Reply
jstlucas
Posts: 96
(@jstlucas)
Estimable Member
Joined: 19 years ago
A Marchini wrote:OK cool. So it did work, you just need to slow the cycles down, that is understandable. I will have to check the PCI spec but perhaps I/O cycles on the PCI bus are slightly faster than the LPC bus.

Anyways, I don't think it is any major deal to get the option back in the driver. I will try to look at it tonight and post. The 595 driver is relatively easy.

Tony M.

I GOT IT WORKING!!!

Thinking that the problem might be with the output of the pci parallel port card not having enough "ooommmppphhh" to drive a ton of chips, I added a couple of inverter chips (7404 variety, not the 74hc14 but close enough) to drive the three signals and the 2nd parallel port drives 192 olsen channels PERFECTLY!!! So, a combination of extended clock pulses and a signal driver is what it took me to get the extra pci parallel port going.

Oh happy days... Now to get KC to post a clock pulse extender for Vixen 2.


Reply
Virtus
Posts: 1182
(@virtus)
Noble Member
Joined: 19 years ago

I used one off TigerDirect a couple years ago that was a two port PCI and while the ports were not re-addressable I was able to tell Vixen to address them on base addresses 1060h and 1050h, respectively. I think it was sold as STARTECH brand.


Reply
A Marchini
Posts: 426
(@a-marchini)
Reputable Member
Joined: 19 years ago
jstlucas wrote:I GOT IT WORKING!!!

Thinking that the problem might be with the output of the pci parallel port card not having enough "ooommmppphhh" to drive a ton of chips, I added a couple of inverter chips (7404 variety, not the 74hc14 but close enough) to drive the three signals and the 2nd parallel port drives 192 olsen channels PERFECTLY!!! So, a combination of extended clock pulses and a signal driver is what it took me to get the extra pci parallel port going.

Oh happy days... Now to get KC to post a clock pulse extender for Vixen 2.

The 74hc14 was just to eliminate any potential slow rise signal problems, but it seems all you needed was a buffer which is always a good idea anyways.
The big issue is driving all those clocks and latch lines at one time, that could be a lot of fan out to work correctly.

It is great that you got it working.
Tony M.


Reply
Page 2 / 2
Share: