Lighted Window Fram...
 
Notifications
Clear all

Lighted Window Frames

21 Posts
10 Users
0 Reactions
8,688 Views
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

I used PVC that friction fits around my windows with the lights mounted on that. Love how easy it went together and how well it worked. I did use 4 finish nails near each corner on the side just to make sure it didn't pop off in a high wind. I'll post a close up picture when I take them down tomorrow.

On my vinyl windows that they won't friction fit around I used stick on tie-wraps.

For me I'll vote for PVC frames any day.


Reply
lightman
Posts: 1524
(@lightman)
Noble Member
Joined: 19 years ago
dirknerkle wrote:Lightman's pictures look just like what you need. The frames I made were out of 3/4" PVC, I made them about 21 years ago. Mine are fastened to wood trim around the windows with pipe clamps, which wouldn't work for you. Friction fit would probably work, but you could also add a couple strips of industrial Velcro that wouldn't be visible at all and would do a good job of securing them.

I believe you were the one that gave me the idea in the first place Dirk!...LOL :biggrin:

I added the pressure clamps for security. Like Timon said, they stay in place with friction.

Regards,
Lightman


Reply
alanp
Posts: 140
(@alanp)
Estimable Member
Joined: 18 years ago

I use 1" PVC pipe and split it down the middle with a table saw, this forms a cavity where I then lay the lights in it and cover the whole thing up with packing tape.

I have used this for 5 years now and they are still doing great. One other tip, for doing around the window, get the measurement you need and make the thing with 90 degree elbows and glue the whole thing together after it dries take that to the table saw and split down the middle.


Reply
MichiganLights
Posts: 479
Topic starter
(@michiganlights)
Prominent Member
Joined: 14 years ago
alanp wrote:I use 1" PVC pipe and split it down the middle with a table saw, this forms a cavity where I then lay the lights in it and cover the whole thing up with packing tape.

I was thinking something very similar. I would like the lights to all align. I'm looking at three channels/colors per frame.

Did you use schedule 40 PVC? Did the slot you cut affect the rigidity? Do you have pictures?


Reply
alanp
Posts: 140
(@alanp)
Estimable Member
Joined: 18 years ago

I did use schedule 40, if your going to put three colors in there, you will want to experiment with the size of the pipe.

Yes, when we cut it in half it became weaker, but nothing we couldn't work with, ours is attached to the house with 1/2 conduit straps bent into a "Z" shape, you just drop the frame into the brackets and your done.

I will see if I can get some pictures for you tomorrow.


Reply
Posts: 2
(@dclark6623)
New Member
Joined: 17 years ago

I made mine out of 1/2" pvc. They look just like dirknerkle's. They fit tight inside the brick window casing. I have used them for 3 years now. They cut my set up time drastically. You will need to think about storage though.


Reply
alanp
Posts: 140
(@alanp)
Estimable Member
Joined: 18 years ago

Here is a couple of pictures around a window and a straight piece used around the garage door.

IMG 7236
IMG 7237
IMG 7238
IMG 7239
IMG 7240

Reply
sonic777
Posts: 154
(@sonic777)
Estimable Member
Joined: 14 years ago

Nice idea on the split pvc and packing tape, I couldn't imagine it until you posted the pictures, I like it and might use that next year.


Reply
alanp
Posts: 140
(@alanp)
Estimable Member
Joined: 18 years ago

This was our 4th season and everyone of them are holding up very well


Reply
Posts: 2
(@dclark6623)
New Member
Joined: 17 years ago

The split pvc looks better than using ty-raps to hold on to the pvc. It's much neater looking. I am going to change mine. Thanks for posting pics. Also, the lights are protected from being broken in storage. I have had problems with breaking a few bulbs every year and having to look for them after plugging everything in.


Reply
Page 2 / 3
Share: