2016 was my first year. I love pixels and lights, but The Mrs. is opposed to making the house look like a rats nest during the daytime. So I set out to design a fixture that was very difficult to see from the street but gave me the most flexibility for lighting and still had a quick install time.
I decided to build a PVC pipe frame in much the same way many people do to mount their Pixels. And I used Matt Johnson's jig and technique for making the holes uniform. Where this differs is that the pipe is then covered with some angled vinyl that serves to mask the PVC frame from view, blend in with the window frame, and provide a place to mount additional lights in the form of a strip.
With the frame in place, I can run c6s pixels, naked 8mms, 60/20 strip, or any combination for varying effects. It's virtually invisible from the street.

To install them I simply let them sit on the window sash and zip tie them to two eye bolts I installed in the bricks at the top. Removing them involves cutting the zip ties and taking them out. About 3 minutes in, 30 seconds out.
I made 5 frames and some holiday coro pixel nets over my bushes for my display this year. Hopefully, I'll get more up for next year and get to do a show.


Here is a video of the construction process. It's long, but the different parts are in comments if you want to jump to a specific part. I'd welcome any veteran commentary on my lighting or construction methods. I'm all home-taught, mostly from this forum and youtube.
Those look very nice. The video does not work for me
Sent from my iPhone using Tapatalk
Hrm. Lemme try and post the video again...
>
Dunno why, but the video button on the post isn't working. here's the link:
Wow! those look really nice. Great work, how long would you say each one took?
MCas_4380 wrote:Wow! those look really nice. Great work, how long would you say each one took?
Hard to say in hours, but the first one took a lot longer than the other 4. Once I had my jigs set up and got the process down I could do everything in batches. Thankfully my house had 5 windows which were exactly the same size so mass production worked. Looking back at my photos it looks like the 4 were started around sept 24th and finished prior to Oct 16th.
But my time on them could vary from <1 hour to 3 or 4 hours per day at the most. Some steps you have to wait for like the glue on the PVC pipes, the vinyl frames, and the c6 lenses to dry. For me, the biggest holdup was painting them. My house's trim is a stupid cream color. If your house has white trim they'll take about half the time with no need for primer or 2 coats of paint since you can get vinyl fencing in white. One advantage of painting it is you can give it a flat finish instead of a gloss one that vinyl typically comes with.
Those look amazing and with such a clean appearance. Great work!
Do you have dimensions for the jig or would you be willing to make another set and sell them?
ChristmasDay wrote:Those look amazing and with such a clean appearance. Great work!Do you have dimensions for the jig or would you be willing to make another set and sell them?
Here is a picture of the jig.
It's simply a section of plywood with two strips attached and a dowel protruding between them. Very simple to build. I have a small block with a hole started in the middle of a set of crosshairs. The way I can set the jig to differing hole intervals is to lower the drill press down into the block and slide the jig along the trench until the crosshairs fall along a premeasured line that I drew on the top of one of the strips. Then clamp the jig to the drill press table so it doesn't go anywhere and you can drill tons of equally spaced holes.
For the construction of the jig simply take a slab of plywood and rip two 3/4" thick or so strip off the edges. glue and screw the square end of that somewhere on the plywood. Then take a pipe and place it next to what you just screwed down. Then grab a second strip and glue that down next to the pipe. That way it's customized for the exact type of pipe you use. measure and find the center of the trough for a dowel and drill a hole for that then put the dowel in and glue it.
At the opposite end of the jig from the dowel is the part I used to get in the center of the cross joint pieces. I just cut a section out of the guide the size of the cross diameter and took a chisel to the guides to shave them down a bit to allow for the increased diameter of the cross joint piece.
There are a few Gotchas:
- You need a different mark for the start holes than the normal interval holes because the start holes are measured from the edge of the dowel and the interval ones are measured from the center.
- Keep the travel of your drill press in mind. You need to be able to drill down far enough to make the hole big enough but also come back up high enough for your pipe to easily come out of the jig while the drill is running and clear the top of the guide strip. My drill press is a piece of junk so my gudies had to be rather low and I could not use my 1/2" step bit. A normal drill press shouldn't have that issue.
- The longer your jig is the easier it will be to do long pipes. If your drill press is not recessed to be flush with a nearby table then a longer jig can help you fight the leverage of a long pipe when drilling holes at the end.
- When you make your jig to your pipe and cross pieces buy the stuff you want all at once from your home center. I bought what I needed for a prototype and by the time I came back to buy the rest they had changed their supplier for the cross pieces and the new ones were a different size. I had to modify the jig for the next 4 I did.
- Make some extra room on both sides of the guides to make clamping the jig to the drill press table easier.
- I made my dowel the exact size of a bullet node by sticking a 1/2" dowel in my drill press and using sand paper until it was .490". that way if the pipe fit over the dowel I knew a pixel would fit in it.
- Keep your trench clear of plastic with a shop vac or the pipe will sit on the cuttings of previous holes and get a sloppy and enlarged hole.
I like my jig and it worked well for the price. I think a new drill press with a longer travel and larger table would help make the process easier, but my shop is very small...and messy.
All of that being said I'm going to be drilling some holes in other diameter pipes for next year and I saw this online so I bought one to try and see if it works better. I'll post back when I have some time with it.

Link






