Notifications
Clear all

Pixel Plane problem

41 Posts
6 Users
0 Reactions
13.2 K Views
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago
[#30496]

Hi all..

I've been trying to get my MT to preview properly for quite a while but have been struggling trying to figure it out but I'm at the end of my patience.....(patience defined as it applies to my lack of understanding)

For the longest I thought it was the preview.....but today I dropped a NC sequence onto my MT RGB channels, not using the PP, and BOOM.....Preview worked exactly as it did in NC....LOOKS GREAT!

The Pixel Plane does NOT work the same way for me. When I go back and drop the same effects (some scrolling text starts the NC effect)into the PP.....It displays but appears to start (looking down on the tree from the top) in the 3:00 position.....and runs counter clockwise to the 7:00 position where the whole text abruptly shifts up the tree by a couple of feet then continues scrolling to the 9:00 position where it shifts back down to the same level it started on.

I have 64 strings assigned (representing my roughly a 270 degree tree) and 85 in the preview to complete a 360 for the preview....So I'm ASSUMING the shift is occurring because of the 270 vs 360 thingy.... But if that is the case......why is anything showing at all as that area should be blank.

I have set the PP up in the 2 steps required to include assigning 64 strings at 60 pix/ea to the big matrix....leaving the additional 21 strings as unassigned.....

Can anyone see where I'm screwing this up? Joe....sorry for the dissertation but I made it as short as I could and still give enough details as to what I'm seeing...


40 Replies
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Create a preview mega tree model that is 2x your desired tree size ( string count only )

assign your actual strings .

all will play nice in preview now

enjoy
Richard


Reply
Posts: 825
 DanJ
(@danj)
Prominent Member
Joined: 13 years ago

At the risk of highjacking... In general, do ya'll use NC and drop the effects into HLS? This is the approach I took with LOR for 2013 Christmas and it worked like a CHAMP. I really like using NC and would like to continue with this approach. But maybe this is not needed with HLS???
Thanks


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Nutcracker has the ability to export generated effects as a .HLSNC File .

This exported .hlsnc file type is then stored/saved in the *\Hls\Nutcracker folder .

Hls users have the option to use this file type in 1 of two fashions

1) Add as an external pixel plane effect to a Pixel Plane channel

or

2) Drop the .hlsnc file directly on a display group consisting of RGB channels.


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago

The preview works fine if I drop NC effects onto the regular RGB channels so the preview setup would seem fine......ONLY when I try to drop the NC effect into a pixel plane does the problem occur......

angus40 wrote:Create a preview mega tree model that is 2x your desired tree size ( string count only )

assign your actual strings .

all will play nice in preview now

enjoy
Richard


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

There is no Dropping on a pp you add an external effect to the pp.

Have you assigned your pixel plane channels in the PP editor ?


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

If you created your Mega tree preview model as I have suggested above and defined your pixel plane as a mega tree and

assigned your strings in the PP editor to suit your 270 ° layout , all effects will appear properly .

That is all I can add to this thread .

It is just this simple .

Richard


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago

I added.....since you can't do it the other way......just mispoke...

And yes....I have assigned them....

At least I can get it to work in RGB.....I'm about ready to just go that direction....I can do it much faster dropping onto RGB channels... I haven't been able to do any sequencing because I'm spending all my time trying to figure out what I've done wrong.....I'm sure it's some tickmark some place that I've missed or don't know to look for.....you don't know what you don't know.........


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

no worries .

I could not get my effects to display front and center on my preview model until i doubled the string count .

your 270 might aswell be a 180 for preview sake is my best suggestion , this way you get to see the whole effect .

How you layout your actual strings will define the 270°

Cheers


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago

Then Why does it display perfectly when I drop the same effect onto the RGB channels? I'm sooooooo confused. I really thought, when I got the RGB channels to display on my preview, that it was set up properly....

Frankly.....it was so painful to set up the preview that I REALLY don't want to go through that again.....

angus40 wrote:no worries .

I could not get my effects to display front and center on my preview model until i doubled the string count .

your 270 might aswell be a 180 for preview sake is my best suggestion , this way you get to see the whole effect .

How you layout your actual strings will define the 270°

Cheers


Reply
Page 1 / 5
Share: