Grinch / Parallel P...
 
Notifications
Clear all

Grinch / Parallel Port Help

15 Posts
6 Users
0 Reactions
9,344 Views
Posts: 16
Topic starter
(@upstech76)
Eminent Member
Joined: 17 years ago
[#12296]

HELP! I have just assembled my first Grinch and SSRez boards. Hooked everything up and it doesn't work. Working my way through the troubleshooting guide I think I am having an issue with my LPT port. The troubleshooting guide states while running the test sequence the pin #2 on the parallel port should alternate between 4 volts and 0 volts. I have a constant 4.3 volts on pins 1,2 on the parallel port. Tried 3 different computers and get the same thing on all of them. I am running EPP but I also tried all the Bios settings. I am using the Olsen 595 plugin in Vixen. Any ideas on what I am doing wrong here?


14 Replies
Aurbo99
Posts: 2804
(@aurbo99)
Famed Member
Joined: 19 years ago

A bit more info please.

Step by step, tell us your procedure...

There are many areas that could be at fault, Plugin channel range, ports, power to the Grinch, Cat5 cables, the type of computer your running etc..

Pictures of your Grinch would help too.

My first year I had issues as well with my Grinch, in the end I was running ECP mode 1.7 if I recall.


Reply
tweist
Posts: 394
(@tweist)
Reputable Member
Joined: 18 years ago

I had some what of the same problem last year with my first grinch boards.
Try using the "Simple 595" plug in. It worked great for me.
Also, make sure your plugin setup is correct. Because I had to use 3 LPT ports last year, I had to install extra LPT boards. I then went to the harware manager under the system configuration of windows to see what the starting address was. It was not the standard 0378 or 0278. it was actually CC50. When I did the port setup in vixen I used "other" and typed in CC50. Then it worked great.
So check under your system icon in the hardware manager for the starting address of your LPT port.

Hope that helps.


Reply
Posts: 16
Topic starter
(@upstech76)
Eminent Member
Joined: 17 years ago

I am following the troubleshooting guide step by step found here:
http://www.doityourselfchristmas.com/wiki/index.php?title=Troubleshooting_Guide_The_Grinch

Computer is a custom home build PC as I built all my PC's. Tried 3 difference PC's one has a MSI motherboard, one has a Abit motherboard, and I tried a factory stock Sony desktop.

Powering the grinch from the Desktop PC power supply 5 volt pins, all power checks out to the grinch, tried using all the bios settings for the LPT port. Bios currently shows me running EPP 1.7. Built a test sequence using the instructions provided in the link above. (2 seconds on, 2 seconds off in a loop with chanel 1 alternate on/off every 25 milliseconds.) Oslen 595 plugin, LPT1 ports 1-64.

The troubleshooting guide states I should have approximately 2.75-4.0 VDC for two seconds and then 0 VDC for two seconds and repeat continuously on Pin 2 on the LPT port which I don't. Per the instructions I checked the vixen plugin, bios settings, and tried different computers which none of worked.


Reply
Aurbo99
Posts: 2804
(@aurbo99)
Famed Member
Joined: 19 years ago

How long is your data cable, from PC to Grinch?

Are ALL pins 18-25 grounded? (This was one of my original problems)

Power to the Grinch, which pin set is it provided to? (Some folks mistakenly place the power on J1)


Reply
Page 1 / 3
Share: