wireless Renard
 
Notifications
Clear all

wireless Renard

8 Posts
3 Users
0 Reactions
3,578 Views
Posts: 255
Topic starter
(@lizard050)
Reputable Member
Joined: 19 years ago
[#7119]

I did a few searchs and didn't find anything definitive. I may have missed something. Was wondering If this is being done econimically by anyone. If not has anyone though about using RJ wireless module he is creating over at DYLA for his DMX stuff and converting their renards to dmx. Not sure if this even possible? I have several renard boards and a Freestyle and would like to try and make some of my renards wireless. My other option would be to go with RJ wireless stuff and get some Lynxx express board but my funds are a little limited this year so I (my wife) would rather not get more controller boards.


7 Replies
Posts: 114
(@tabor)
Estimable Member
Joined: 18 years ago

The Renard boards work quite well with the Xbee modules, They are very easy to set up and provide good speed and distance.

They are the same modules used on the new helix board.

I don't know how easy (or if possible with the current firmware) it would be to daisy chain the boards wirelessly.

I have only experimented with one REN64 to one serial port.
The xbee modules can be found at sparkfun.


Reply
cbell
Posts: 462
(@cbell)
Honorable Member
Joined: 18 years ago

I'm currently running my Ren24s with the DMX firmware with no problems thus far, however with 2009 being my first year, they haven't been "show tested". My plan is to run RJ's wireless with my renards. I haven't seen anything to make me think it won't work. Not quite as elegant of a solution as just going with expresses and the built in wireless, but since I had already purchased my 24's before I found out about the expresses, I'll use what I have :). I'll be posting updates to my blog as I get and play with the Lynx wireless stuff.


Reply
Posts: 255
Topic starter
(@lizard050)
Reputable Member
Joined: 19 years ago

cbell , just read your blog. Did I read it correct that all you did to get your ren24 to run dmx in install the dmx firmware and change cat5 cable wiring to convert the dmx from the dongle to the renard pin out. If that is all then why the need for the dmx adapter board? I have several of the 1 run of those boards but I don't believe anyone got them to work.


Reply
cbell
Posts: 462
(@cbell)
Honorable Member
Joined: 18 years ago
lizard050 wrote:cbell , just read your blog. Did I read it correct that all you did to get your ren24 to run dmx in install the dmx firmware and change cat5 cable wiring to convert the dmx from the dongle to the renard pin out. If that is all then why the need for the dmx adapter board? I have several of the 1 run of those boards but I don't believe anyone got them to work.

That is correct. I just used some cat5 keystone jacks that I had laying around and changed the pinout going from the DMX dongle to the renard. Once the DMX firmware was on, it worked with no problems. I've been playing around with the one here in the basement for several weeks now and haven't noticed any major problems.

The only real reason I'm planning on using the adapter board is because I think it will be easier to deal with than finding a way to mount the keystone jacks in the box (although they could just be stuffed in there I suppose). The other reason is the onboard termination, but as I've discovered since I don't currently have the boards, a terminator can be easily made using a cat5 end and a 120R resistor across the DMX data pair.

All the adapter board is doing is changing the wiring and adding the terminating resistor and jumper. I think there may be an option for injecting power/ZC for a REN-C, but I haven't looked into that further because it doesn't apply to the Ren24s.


Reply
Page 1 / 2
Share: