SSRez channel on so...
 
Notifications
Clear all

SSRez channel on solid question

12 Posts
6 Users
0 Reactions
3,604 Views
JasonPortwood
Posts: 753
Topic starter
(@jasonportwood)
Noble Member
Joined: 17 years ago
[#17283]

So I have my display up and running and things went great. Then I smelled that burning electronic smell in the air. I wasn't smart enough to figure out I had a problem so a couple hours later I was testing and a couple channels refused to turn off on one SSRez.

One channel has 4 sets of candy canes (3 each) and 6 rope lights.
Another had 10 C7 bulbs, a couple 50 count strings of incandescent, and two blow molds - large not sure the bulb inside.

I swapped out the SSRez, like a newbie, figuring I soldered something wrong and put another in it's place. Then I stuck channel 3 on on that one. I didn't leave this one alone like I did the last one so more damage adverted (I hope).

The first SSRez board is burned with two channels stuck on and the triacs are discolored.
The second one looks OK on the board but the channel is stuck on without being hooked into a Renard 64.

I finally got smart and got out my kill o watt and tested the load. I'm pulling 2 AMPS on each of those channels. The other two chanels minimal with 1 C9 for a north pole and a long string of LEDs...

My question is this.

Reading the trouble shooting page it looks like I have messed up the triacs. Would swapping those out be the fix (since they are burned on one board) or do I need to worry about other parts? Could there be other causes that I am overlooking?

Also how much load can I put on a channel for a SSRez? I talked with Kelly but he doesn't know the exact number for that, he never puts more than a couple things on a channel. I of course learned my lesson now. I got lazy and could have split those rope lights up more. Wish I had.

Thanks for any advice.

Jason


11 Replies
Posts: 1372
(@fathead45)
Noble Member
Joined: 18 years ago

ive ran about 2.5amps thru each output on mine. so i was pulling a total of about 10 amp thru my ssr for my show last year. now i dont recommend it but i was doing and knew i was taking a chance. so i would think it could handle it but i did have heatsinks on all of mine.


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

I would swap the triacs and the resistors that feed the triacs.
HEAT kills all electronic components.
I think 2 amps a channel is too much for the SSRez.
The board has 1 ounce copper, so I would figure about 1.5 amps max a channel, maybe 1.75. This is with heatsinks !
If you need more then 1.75, I would suggest moving to the SSRneon


Reply
wjohn
Posts: 1102
(@wjohn)
Noble Member
Joined: 19 years ago

SSRez is 2oz copper, as long as you have decent heatsinks you can run the channels at 2 amps, for a maximum of 7 amps for the board.

I have always specified my SSR boards at 2oz, (DC SSR, SSRez etc)

When I put the first SSR together, I tried a destructive test with 4 amps on one channel, without a heatsink, the Triac turned grey and there was some heat damage to the silkscreen. I would not recommend it, but I did test to the extreme.

The SSR was tested during a 70 f deg day, with the SSR in side a cg-1000 case.


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

OH !
That is good to know! Sorry for the wrong answer.

wjohn wrote:SSRez is 2oz copper, as long as you have decent heatsinks you can run the channels at 2 amps, for a maximum of 7 amps for the board.

Reply
Page 1 / 3
Share: