Ren16 regulator pro...
 
Notifications
Clear all

Ren16 regulator problem

15 Posts
5 Users
0 Reactions
4,408 Views
Posts: 32
Topic starter
(@brett)
Trusted Member
Joined: 18 years ago
[#6909]

Having problem getting ren16 to work.
5v regulator is only outputting 2.5 v and getting realy hot.
Now pic u2 also getting really hot to touch, pic u1 is ok, not hot at all.
I think the 1 uf caps either side of the regulator might be the wrong type.
They sent me 1.0uF 50V Multilayer Ceramic Capacitor, could these still work or do they have to be monolithic.


14 Replies
RichF
Posts: 1356
(@richf)
Noble Member
Joined: 19 years ago

Check your solder joints. Sounds like you have some joints bridged that should not be. Also are you refering to the IC chips U1 and U2. On the Schematic U1 is the regulator and U2 is the H1AA1 chip.


Reply
omzig
Posts: 1603
(@omzig)
Noble Member
Joined: 19 years ago
RichF wrote:Also are you refering to the IC chips U1 and U2. On the Schematic U1 is the regulator and U2 is the H1AA1 chip.

That is assuming that he is building an SS16. On the XMUS 16 the PIC's are U1 and U2.


Reply
RichF
Posts: 1356
(@richf)
Noble Member
Joined: 19 years ago

Ahh thanks for the Catch. I thought he said he was building the SS16. I see now in another post where he is building a XMUS ren16.

Now that I am thinking about the Xmus ren16 are you supplying the 12vdc to the board? I had a ren16 that I fixed for someone else and had low voltage at the regulator and turns out I was not suppling the 12vdc to the board as it needs.


Reply
Posts: 32
Topic starter
(@brett)
Trusted Member
Joined: 18 years ago

I'm building the ren 16ss, the hot chip I refer to is the 16f688 near the regulator. I am also bringing power in from a standalone tranformer aand connecting it to tp1 and tp2. This set up worked for the ren24's I recently built from wayne but not with the boards from John.


Reply
RichF
Posts: 1356
(@richf)
Noble Member
Joined: 19 years ago

I do not see a TP1 and TP2 on the board. where are they located on the renss16?


Reply
Posts: 32
Topic starter
(@brett)
Trusted Member
Joined: 18 years ago

I am using the ren 16 ssr rev 1.9.1.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Possible causes for the PIC running hot is installing it backwards, too high a power voltage (or reverse polarity), a shorted output, or maybe a problem when programming it.


Reply
Posts: 919
(@scorpia)
Noble Member
Joined: 19 years ago

brett,

the ren-16's from wjohn are a little different when it comes to inputing power to wayne's "ss" series of boards.

for inputing the power If your using tp 1 and tp2 you should be ok. i normally use the pads located just under the words "IN" or "OUT" just above the rj45 connectors. as they are joined to tp 1 and tp2 you should be good.

also double check the 5v regulator and see if its facing the wrong way. the heatsink side should face into the board not out as would normally be expected.

last thing is also are you supplying 12v DC or 12v AC. this board is designed for 12v DC in not AC.

See if they helps

Peter


Reply
Posts: 32
Topic starter
(@brett)
Trusted Member
Joined: 18 years ago

OK, from the start.
I have built and tested 3 x ren24ss boards from wayne, same regulator , same 12v input. No problems there, they ran no worries.
I am now bulding and testing 3 x ren16ss xmus boards, but cant get past the 5v test point using same regulator and same 12v input.
I can now get 5v at test point on one board but PIC still gets very hot.
On the ren24 boards the regulator didnt event feel warm, on these boards it gets red hot in a matter of secounds.
Is there a differnt fimware for the ren16 vs ren24 boards?
Have checked all three boards for solder bridges, whats the chances of all three boards having faulty solder bridges at the same point.
Pin 1 and 14 on the pic show 5v
All others show .5 v except for 14 and 2 show 1v and 14 and 12 show 1.5v.


Reply
Page 1 / 2
Share: