I have looked through the forums and on the wiki in regards to the ren-w, but couldnt find my answer. First, I'm not sure if a ren-w can before used with a ren-24hc, couldn't find that listed on the wiki. If somebody knows, or knows how to mod the board, please let me know. If I have to go with the ren-24 ss version, no biggie. I was going with the 24hc because you can buy the BOM and pcb as a kit over at wlc. I seen a thread here a guy always having the ss boards and has the parts list for mouser.
Second, if I had 4 boards and wanted to use a ren-w, would I have to have those for every board ? I ask because this coming year will be my first year, and the wife dont want wires ran out the house. So I'm asking if I can have the first board on a ren-w, so no wires are coming from inside the house, and hook my other 3 boards in line with cat 5 from the first board?
And I'm trying to do my parents house next year, if time permits. They have a driveway through the middle of their yard, so really dont want cat 5 and everything getting drove over.
Sorry if this has been covered, maybe its a dumb question, but I'm new and trying to understand everything gets overwhelming. I have been trying to read as much as I can and soak the information up.
Thanks in advance.
The Ren24HC is the same as a Ren24 with thicker copper for the power section, bigger triacs, etc. Ren-W works fine with the Ren24HC when you use it in Renard mode. If you plan to use DMX with the HC, then Ren-W is not a good choice.
You can use Ren-W from the house to the first one and daisy-chain the other Ren controllers off that. When you daisy chain multiple Renard controllers, they act, more-or-less, like one big controller. So 4 Ren24's connected together would be akin to a 96-channel Renard. What's more, you can use a USB XBee Explorer board at the PC as your transmitter and put a single Ren-W in your first controller outside, and then you only need one Ren-W. Or you can use a Ren-W as the transmitter and another one as the receiver.
For the MOST flexibility, and to eliminate cat5 altogether, you can put a Ren-W in each controller and use start_address firmware in them to assign the proper channels to them.
So there's lots of flexibility. The amount of data available can be overwhelming -- it's good that you asked for clarification!
Merry Christmas!!!
I appreciate the quick response. Yeah the amount of information I seeing is a bit much for a first timer. Thats why I took my time reading the wikis and the different threads before posting anything. My question might have seemed small, but I like knowing how everything works, and how my design will go together before buying and starting.
I wont have any DMX. I want to have all my boards wireless, depending on if money allows and if I can get the boards and vixen for myself and parents working correctly. If not, then at least on my first board. I plan on the XBEE Pro at the pc transmitting to the ren-w at the first control board.
Thanks Again for the help. I'm sure Ill have a lot more questions once gear starts arriving.
Merry Christmas.
Dirk, would he be ok daisy chaining 4 boards or could he run into timing issues after channel 54 (or so)?
Thanks,
-joni-
rjchu wrote:Dirk, would he be ok daisy chaining 4 boards or could he run into timing issues after channel 54 (or so)?Thanks,
-joni-
It seems okay if you're using the Mark parity and 2 stop setting on Vixen and the Xbee. You only get the problem when you run in the normal "stock" mode, 57600, N,8,1
Would it be better to just put them all wireless then and have then xbee pro fire signal to all of them at once? I read in the wiki where you can set it up for all ren-w receive signal at same time so theres no timing issues. I was just afraid if I try doing 8 ren 24hc, 8 ren-w and sequence as a first timer, I would have problems. Guess if I get the first board built without to many problems, and the other 7 follow, I could go for all wireless. If I went all wireless, then next year if I add a ren-64, I can just add another ren-w. Still unsure how many can be controlled off one port, and how many boards can flow smoothly off an xbee pro.
Thanks Dirk for correcting me, I keep mixing up the 8N1 and 8M1 rules now that I'm starting to play with the E1.31 DMX/Ethernet bridge. 🙂
Chad, to (hopefully) address your concerns, I'm running in this mode (global broadcast I think it's call) with just one transmitter and at the longest receiving end have 3 Ren24SS boards daisy chained and don't have any issues with timing or sync to the music. My first year of experience with the XBee/RenW combo is that it's pretty rock solid and MUCH easier than running cables everywhere like I did last year.
Once again, many thanks to Dirk for contributing the RenW solution!
-joni-
chadowamsley wrote:Would it be better to just put them all wireless then and have then xbee pro fire signal to all of them at once? I read in the wiki where you can set it up for all ren-w receive signal at same time so theres no timing issues. I was just afraid if I try doing 8 ren 24hc, 8 ren-w and sequence as a first timer, I would have problems. Guess if I get the first board built without to many problems, and the other 7 follow, I could go for all wireless. If I went all wireless, then next year if I add a ren-64, I can just add another ren-w. Still unsure how many can be controlled off one port, and how many boards can flow smoothly off an xbee pro.
So if I run global broadcasting setting, I can go wireless on some and wired on some. If I have a couple boards close together, no reason for me to get other ren-w's my first year. I can just wire those together. Saves me a little money since if was a bit difficult talking to the wife into letting me spend the money for 4 ren 24 boards and 100 new strands of led.
I guess you assign which channels are wireless in vixen ? Thats where I was getting confused. I was having a hard time grasping how first board could be wireless, then the next two be wired into the first, and then last one be wireless.
Thanks again. Just waiting for the group buy on boards next month and Ill be ready to go. Playing around with vixen now.
chadowamsley wrote:Would it be better to just put them all wireless then and have then xbee pro fire signal to all of them at once? I read in the wiki where you can set it up for all ren-w receive signal at same time so theres no timing issues. I was just afraid if I try doing 8 ren 24hc, 8 ren-w and sequence as a first timer, I would have problems. Guess if I get the first board built without to many problems, and the other 7 follow, I could go for all wireless. If I went all wireless, then next year if I add a ren-64, I can just add another ren-w. Still unsure how many can be controlled off one port, and how many boards can flow smoothly off an xbee pro.
At 57600 baud, which is the maximum speed an XBee can handle data, you can have up to 286 channels on the same port. So your 8 Ren24HC's would total 192 channels, and you're plenty safe and have room to grow before you'd need to use more than 1 port. However, if you had 2 ports, you could also put half of them on one port and half on the other. You can assign which port controls which channels in Vixen.
chadowamsley wrote:So if I run global broadcasting setting, I can go wireless on some and wired on some. If I have a couple boards close together, no reason for me to get other ren-w's my first year. I can just wire those together. Saves me a little money since if was a bit difficult talking to the wife into letting me spend the money for 4 ren 24 boards and 100 new strands of led.I guess you assign which channels are wireless in vixen ? Thats where I was getting confused. I was having a hard time grasping how first board could be wireless, then the next two be wired into the first, and then last one be wireless.
Thanks again. Just waiting for the group buy on boards next month and Ill be ready to go. Playing around with vixen now.
With 192 channels, the simplest solution is to daisy-chain all the Ren24HC's out in the yard and run a single serial cable from the PC to the first Ren24HC. One port on your computer, and it's a done-deal.
A simple wireless solution would replace the serial cable with the USB XBee explorer at the PC and a Ren-W at the first Ren24HC. You'd leave the rest of it exactly the same except instead of configuring the Renard plug-in to go out your normal serial port, you'd set it to go out the port where the USB Explorer is (might be COM3 or COM4, etc.)
But the MOST flexible solution would be to use a USB Xbee explorer at the PC and a Ren-W at EACH of the Ren24HCs. Then you would not need to connect all the Ren24HC's together with cat5 in a daisy-chain. Instead, you'd use start_address firmware in each Ren24HC to choose it's proper channels out of the total 192 that would be broadcast from the PC.
EDIT: Whoops, sorry Dirk, didn't know you replied as well - guess that's what I get for not refreshing before replying! 😉
Exactly right. In my case I have some Ren24's that have a RenW in the enclosure with them and the pair is standalone. In other cases I have a Ren24 with a RenW in the enclosure and cat5 that goes from that Ren24 to another one downstream, and another and another. You can have as few or as many (I think) as you want attached to a RenW.
As far as Vixen goes, you don't have to do anything special. You just number your channels and lay things out as you would normally however, you do have to keep the channel numbers contiguous for the controllers you want to group together/daisy chain off of a single RenW. Then, for the controller that directly attached to the RenW, you reflash ONLY THE FIRST PIC with the start addressable firmware http://www.doityourselfchristmas.com/wiki/index.php?title=Renard_Start_Address_Configuration_Guide and it'll ignore any channel numbers before the start address mapping, consume the number of channels it can support, and then pass the remaining data on to the next controller that's hardwired to it. The WIKI page I've linked to describes this pretty well but if you have other questions feel free to ask.
Thanks,
-joni-
chadowamsley wrote:So if I run global broadcasting setting, I can go wireless on some and wired on some. If I have a couple boards close together, no reason for me to get other ren-w's my first year. I can just wire those together. Saves me a little money since if was a bit difficult talking to the wife into letting me spend the money for 4 ren 24 boards and 100 new strands of led.I guess you assign which channels are wireless in vixen ? Thats where I was getting confused. I was having a hard time grasping how first board could be wireless, then the next two be wired into the first, and then last one be wireless.
Thanks again. Just waiting for the group buy on boards next month and Ill be ready to go. Playing around with vixen now.
