HELP! Ren 24
 
Notifications
Clear all

HELP! Ren 24

14 Posts
5 Users
0 Reactions
3,686 Views
Posts: 66
Topic starter
(@bbayliss)
Trusted Member
Joined: 19 years ago
[#5415]

Could someone please give me some help. I have 4 REN 24 V2.5 and I have 6 REN24 V3.3 that I am building. I know that there was an error on version 2.5 that the input pins were swapped. I do not have any communications from one REN24 to the other. All of my controllers work, but as I was testing them it was one at a time, now that I have them all daisy chaned they do not work. I did cross the 2 resistors between the RS485 chips, I read on a thread that this would convert REN24 V2.5 to the standard.
Any help would be very appreciated. My show is dead since no data can get downstream.
Thank you,
Brian


13 Replies
Virtus
Posts: 1182
(@virtus)
Noble Member
Joined: 19 years ago

Pinout for the Renard 24 Version 2.5 Cable:
DB9 Pin 3 to RJ45-pin 5
DB9 Pin 5 to RJ45-pins 1, 2, and 4

Pinout for the Renard 24 Version 3.0 Cable:
DB9 Pin 5 to RJ45 Pins 1, 2, and 5
DB9 Pin 3 to RJ45 Pin 4


Reply
Posts: 66
Topic starter
(@bbayliss)
Trusted Member
Joined: 19 years ago

I do not have a problem getting serial control to each of the controller, it is only when I connect controller 2 to controller 1. No downstream data from controller 1 and I have swapped out controllers so it is not just one of them.
Thanks,
Brian


Reply
Virtus
Posts: 1182
(@virtus)
Noble Member
Joined: 19 years ago

You will have difficulty running 10 Ren24s off a single serial port if you are using the familiar 50 msec timing in Vixen.

Would it work to run all the 3.3 boards off one serial port and the 2.5 boards off a different one? I think 6 Ren 24s is all a 57600 port can support well at 50 ms.


Reply
Posts: 66
Topic starter
(@bbayliss)
Trusted Member
Joined: 19 years ago

I am planning on running them on different serial ports, however I want all of my hardware interchangeable. I also have 3 REN64 XB. I just do not understand why I can not connect 2 REN 24 V2.5 and have them work.

Is there anyway to test the RS485 output?
Thanks,
Brian


Reply
tonypgst
Posts: 399
(@tonypgst)
Reputable Member
Joined: 19 years ago

Your boards may work individually if you are using the same cable to connect and test each one at a time, but what about the cable you are using between boards? Have you only tested using the same one? Did you make it yourself, or it is purchased? Have you swapped out the cable used between the boards? Version 2.5 to 2.5 should pass data, but as I understand it, you will need to cross the pins that are different from a version 2.5 to 3.3.

Unless you goofed on all boards output hardware, I would suspect a cable. Especially between like boards.


Reply
omzig
Posts: 1603
(@omzig)
Noble Member
Joined: 19 years ago
Virtus wrote:You will have difficulty running 10 Ren24s off a single serial port if you are using the familiar 50 msec timing in Vixen.

Would it work to run all the 3.3 boards off one serial port and the 2.5 boards off a different one? I think 6 Ren 24s is all a 57600 port can support well at 50 ms.

That chart is based on the old Renard plugin (even though the note in the wiki says that it isn't). For the newer modified Renard plugin, dimmer levels 125-127 are avoided so the numbers in the chart can be doubled. This was discussed here.

I have tested 7 Ren24's at 57600 and 50ms and it worked great.


Reply
Virtus
Posts: 1182
(@virtus)
Noble Member
Joined: 19 years ago

Is this correct? If you connect a single V2.5 it works okay but you can not get a second one to work down stream with a straight through Cat5 patch cord?


Reply
Posts: 265
(@phenagan)
Reputable Member
Joined: 19 years ago

Silly question, but do you have the plug-in set to the right number of channels? If it's set at 24 channels, you'll never get any data downstream as there isn't any to send on.


Reply
Posts: 66
Topic starter
(@bbayliss)
Trusted Member
Joined: 19 years ago
Virtus wrote:Is this correct? If you connect a single V2.5 it works okay but you can not get a second one to work down stream with a straight through Cat5 patch cord?

Yes this is exactly what is happening?


Reply
Page 1 / 2
Share: