Fried Board ? ? ? ?
 
Notifications
Clear all

Fried Board ? ? ? ?

37 Posts
14 Users
0 Reactions
11.8 K Views
Posts: 139
Topic starter
(@tomperro)
Estimable Member
Joined: 13 years ago
[#34559]

Came home to this tonight!
It was raining and I decided last minute to run the show anyway, bad idea!

I have them in a 15 gallon tub, but I guess moisture got in.

Any ideas on how I can test it to see if I can repair it or not?

10421189 10153382177073626 6486491726498453124 n

36 Replies
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
tomperro wrote:Came home to this tonight!
It was raining and I decided last minute to run the show anyway, bad idea!

I have them in a 15 gallon tub, but I guess moisture got in.

Any ideas on how I can test it to see if I can repair it or not?

Well - - for sure pull the obviously blown TRIACs an clean up the board up from the carbon and then you can start the debugging process.


Reply
Posts: 139
Topic starter
(@tomperro)
Estimable Member
Joined: 13 years ago

Brian,
I purchased this board already assembled. Is there a tutorial or some type of documentation on debugging?


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
tomperro wrote:Brian,
I purchased this board already assembled. Is there a tutorial or some type of documentation on debugging?

The Wiki has troubleshooting steps - but it's primarily aimed at making sure new boards work versus boards with obvious damage. Unfortunately it will be necessary to remove the board from the enclosure to fix it. For sure I can see at least one or two blown TRIACs. You'll need to do some measurements here and there to make sure it's good to go back out or you may risk blowing up more stuff on it. It's one thing to make enclosures weather-proof but always assume that water *will* get in and put in some weep holes or something so that any water that does get in can get out.


Reply
Posts: 838
(@strother85)
Prominent Member
Joined: 15 years ago

Ouch. This is my worst fear. This is why I have 2 - 3/4" pvc pipes about 12" longer than the cableguard enclosure mounted to the back of the enclosure and then drive rebar in the ground and slide the pvc over the rebar so that the enclosure is 12" off the ground and upright so that any water will drain out the wire entry holes. I also tie a heavy duty garbage bag over each enclosure. Like I said my worst fear, so I'm a little paranoid in my setup lol.

You are going to want to get a desoldering solder sucker tool to get those triacs out. Like this one http://www.radioshack.com/radioshack-45-watt-desoldering-iron/6402060.html?utm_source=GooglePLA&utm_medium=pla&utm_term=6402060&cid=iP:PLA:RSO:Google#.VIPxjzHF9t4 .


Reply
Posts: 139
Topic starter
(@tomperro)
Estimable Member
Joined: 13 years ago

Ok, might tackle this today.
Do you know where I can purchase new triacs?
Are the Triacs specific to this board or would radio shack have them?


Reply
Wayne J
Posts: 7789
(@wayne-j)
Illustrious Member
Joined: 20 years ago
tomperro wrote:Ok, might tackle this today.
Do you know where I can purchase new triacs?
Are the Triacs specific to this board or would radio shack have them?

Radio Shack will not have them.


Reply
imbluenote
Posts: 1615
(@imbluenote)
Noble Member
Joined: 15 years ago

You might add you location. Someone local might be able to assist with the repairs as well.

Your best bet for the triac is going to be mouser, Newark, or one if the other online parts co. I looked before and the shack didn't have them for online ordering.


Reply
Posts: 139
Topic starter
(@tomperro)
Estimable Member
Joined: 13 years ago

Oh OK. Thanks.
I'm in mount holly, nj


Reply
Posts: 1115
(@11bravo)
Noble Member
Joined: 14 years ago

My curiousity has got the best of me, I have to ask, why did you set the controller in a tub.


Reply
Page 1 / 4
Share: