Daisy Chain
 
Notifications
Clear all

Daisy Chain

13 Posts
4 Users
0 Reactions
4,039 Views
toodle_pipsky
Posts: 1285
Topic starter
(@toodle-pipsky)
Noble Member
Joined: 19 years ago
[#9331]

Howd'y all!
I've had the serial card in my Vixen computer die - how convenient - so in the mean time while I'm waiting for the replacement I thought I would daisy chain just to keep the setup going. I have a Ren 16 (Xmus) and a Ren C and I can't seem to get them to work in any order - can they be daisy chained to begin with? I thought I did this last year but I guess it must have just been 2 Ren Cs only.

So is it do-able? And if so what should I be checking to troubleshoot?

Thanks heaps and merry christmas lights. 😉
Ingrid


12 Replies
Posts: 919
(@scorpia)
Noble Member
Joined: 19 years ago

TP,

the renard serial comms can be daisy chained from one board to another.

the hard part is making sure each board still has the power it requires and ZC etc. I know with my setup i send ZC signal down the cat 5 to the ren-c and i send power down the cat 5 for the ren16. so i know with my setup it would be hard.

so double check your power and ZC and make sure they arnt getting put on the extra pins on the connectors etc but overall it should work

Peter


Reply
toodle_pipsky
Posts: 1285
Topic starter
(@toodle-pipsky)
Noble Member
Joined: 19 years ago

Haha - see I couldn't just leave it alone could I? Glad you replied, couldn't remember what you said last nite in chat.

Righto, so I send the 12vdc down the cat5 to the Ren 16 (didn't know you could do it any other way) and the ZC is on board. The Ren C - I have 2 of those, one with ZC through the cat5 other with it off board. Was trying it with the ZC through the cat5, might try the other one - would that make a difference?


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Remember that pins 4 and 5 on the RJ45 cable for an xmus Ren16 (non-SS) are 'backwards' from those on the Ren64.


Reply
toodle_pipsky
Posts: 1285
Topic starter
(@toodle-pipsky)
Noble Member
Joined: 19 years ago

Magically worked tonight . . . . did unplug and replug in a few things, so probably just a plug not quite connecting properly.

One thing I did notice is the LEDs didn't really like the whole thing, most incandescant lights were fine. My mini trees are LEDs on a Ren 16 (xmus), 3rd board in the chain and they didn't work properly (turned on/off at the wrong time and just stayed on). The last board another Ren 16 didn't work at all, it had power but didn't turn it's lights on. I just put this down to pushing the limits of what you can run on a single port - hopefully the new serial card will arrive tomorrow.

Thanks for your help. 🙂


Reply
Posts: 919
(@scorpia)
Noble Member
Joined: 19 years ago

TP

great to hear its almost working.
Its seems a little strange that one of the ren-16's isnt working. I would be interested to find out whats going on.

Unless your up over 300 channels per serial port then i dont think its a port limit.


Reply
blurp
Posts: 279
(@blurp)
Reputable Member
Joined: 19 years ago

One of my com ports died, so I'm running 480 channels through one port.

One of my sequences is at 25ms.

The video camera can sense the latency, and they can sometimes come on in different frames, but the naked eye can't.


Reply
Posts: 919
(@scorpia)
Noble Member
Joined: 19 years ago

TP,

as a test can you either take the 3rd board out of the loop or swap the 3rd and 4th boards


Reply
toodle_pipsky
Posts: 1285
Topic starter
(@toodle-pipsky)
Noble Member
Joined: 19 years ago

Interestingly noticed flickering with the incandescents tonight as I hooked up more lights. However, run 1 Ren 16 by itself and it's fine. 2nd Ren 16 still doesn't work, but I think I've hooked the AC up wrong. The 2 Ren Cs seem to work ok in series though.

Anyway will test tomorrow and hope this card arrives! Gotta have it working, it's the first night of the local comp on the 9th!


Reply
toodle_pipsky
Posts: 1285
Topic starter
(@toodle-pipsky)
Noble Member
Joined: 19 years ago

Okay, new serial card arrived - for some reason the 2 Ren Cs and 2 Ren 16s daisy chain together no worries.

On a side note, the second Ren 16 did work and has now quit working. The 24VAC in wire was getting very hot, so changed it out for larger guage wire and it doesn't get hot, but now the lights don't work. I get 24VAC by testing the 2 points it enters the board, tried changing out the h11a1 (or what ever it is) and reflashed the pics. That's about all I can think to do, any suggestions of other stuff to try?


Reply
Page 1 / 2
Share: