board leds do not f...
 
Notifications
Clear all

board leds do not function

12 Posts
6 Users
0 Reactions
4,090 Views
Posts: 281
Topic starter
(@bert-nc)
Reputable Member
Joined: 18 years ago
[#13126]

between myself and my son we have put together 3 of the renard ss16.

have played sequences on all three, the lights hooked to the outputs come on, but no leds on board expect power led light up. I went thru the beginners set-up guide and everything ran worked fine. There must be something simple going on, that is not right. any suggestions would be appreciated.

bert-nc


11 Replies
Posts: 123
(@randyn)
Estimable Member
Joined: 17 years ago

Make sure you have a jumper on JP3

Channel Led
2 HB
5 ZC
6 SD
7 FE
8 DE

Randy


Reply
Wayne J
Posts: 7789
(@wayne-j)
Illustrious Member
Joined: 20 years ago

also, look closely at the resistor network to make sure it is in correctly.


Reply
Posts: 190
(@harpster)
Reputable Member
Joined: 17 years ago

I just built my first Renard SS16 and when I run the beta diagnostic code all the LED''s light up in sequence and are bright. But when I run the Operational Firmware (with J3 in) the lights (except pwr) are very DIM. So for example if I turn on Channel 8, the red DE LED turn's on but I'd miss that in a bright room

Actually when I read this post I didn't remember the LED's turning on at all with the operational firmware so I just checked that and noticed that they light up, they're just not very bright. I assume this is opto and LED are in Parallel with J3 in. I thought I read that it was OK to leave J3 in but seeing this I'll probably take it out.


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago

My guess is eithe Resistor Network or LEDs installed backwards. Of course, I have never done that. (...he says while hanging head low in shame).

My first Ren 64 has 8 LEDS that work. I installed them all backwards and then discovered that I was doing more damage than good trying to fix them. Took me an hour to resolder 8 LEDS. It doesn't look as cool, but the board works.


Reply
Posts: 190
(@harpster)
Reputable Member
Joined: 17 years ago

The resistor network is installed correctly with Pin 1 on the left side in the square. Like I said with the diagnostic firmware they are bright, but with the operational firmware they are so dim I need to look at the center of the LED to see it lit. I thought that the original poster my have not noticed that they were on because of being dim... however if what I'm seeing is not correct I'd like to fix that. Maybe I'll pull out an opto to see if it get's brighter but other than that the board appears to be fully functional.


Reply
Posts: 1424
(@oldcqr)
Noble Member
Joined: 18 years ago

You are probably using the 'standard' firmware and not the PWM firmware. But it really doesn't matter as long as the board is working, AND you are not using LED strings.

The Diagnostic LEDs are pretty pointless when using the production (IE not the diagnostic) firmware. They are just going to light up when the associated channel comes on (as per randyn's post).

The Diagnostic firmware has PWM turned on, so your LEDs will be nice and bright. PWM basically sets the line HIGH for the entire time a channel should be on, where as the NON PWM just sends a pulse. The pulse is enough to keep the triac on for the entire cycle, but not enough to light the LED.

You have 2 options:

Use the PWM firmware, and watch the LEDs blink when the channels do their thing. You won't have to worry in the future if you go from incans to LEDs

Keep using the NON PWM firmware with your incans and ignore the fact the LEDs don't light.


Reply
Posts: 190
(@harpster)
Reputable Member
Joined: 17 years ago

Thanks that was GREAT information! THis solved two problem for me, 1st it explained why I wasn't seeing the status LED's in the operational mode. I went back to the firmware and changed the Define PWM from 0 to 1, assembled and programmed the PIC's. Now the status LED's are full on. I understand that they are not that useful in the operational mode but was really wondering why they were dim. I'm also guessing the the originator of this post may have had the same issue and maybe they already figured out what to do.

Second and most important my pre-assembeled LED Snowflake and LED light strands are working without the need of a terminating resistor (I posted about that today). I might need to add some later if I see anything flakey but right now in my garage it's looking pretty good!

Now a few observations...

1. In the Firmware wiki under Regular Firmware is says ". The drawbacks of non-PWM operation is that it will not properly control any channel status LEDs (present only on the Renard64 board)..." Maybe the part about present only on the Renard64 board should be changed? Also maybe say that the status LED's will appear DIM in this mode.

Not that I read all this clearly myself but it might help some other first timers.

2. In the firmware (renard-20071229.asm file) there is a not about this but it doesn't mention anything about LED lights. Maybe that should say

;; PWM_build can be either 0 or 1
;; Set PWM_build to 0 for Incandescent Lights (30us pulse width)
;; Set PWM_build to 1 for LED Light Lights (variable pulse width)
#define PWM_build 1

;; DC_build can be either 0 or 1 (it should be 0 if PWM_build is 0)
#define DC_build 0

3. Maybe in the standard firmware the PWM_build should be set to 1 as the default since so many people are using LED's. I'm sure there much be Pro's and Cons for doing this but I couldn't tell you what they are... it's just a suggestion if it makes sense and I'm not into this far enough yet to know for sure.

Anyway I really appreciate your comments because now I think I have a better board for my situation. -Alan


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago

Great Harpster. Glad you got it all figured out. Other than Power Consumption for the board, it really doesn't matter if you just use the PWM setting on all Firmware. All of my boards are running PWM fw.

Leave it to those Senior members to go right to the simple and correct solution!

Kelly


Reply
Posts: 190
(@harpster)
Reputable Member
Joined: 17 years ago

Yeah that last bit of information tied up some loose ends on the hardware. Now it's on to Vixen - man I'lll be lucky if I get lights up and one tune sequenced this year! Here's a pict of the completed unit.

SS16 Demo

Reply
Page 1 / 2
Share: